The answer to this question is it depends. Generally speaking, shiplap typically does not go behind trim but rather can be used in place of molding or other trim. The one exception is in cases where shiplap is used to build a box or some sort of other accent feature, where it is then covered in trim afterwards.
In such cases, shiplap will usually go behind or inside the trim. Ultimately, the installation of shiplap will depend on how it is being used. It is recommended to consult a qualified contractor or designer to ensure proper installation.
How do you finish trim in shiplap?
To finish trim in shiplap, you need to measure and cut the trim pieces to fit the space. Start by measuring the top of the wall and the ceiling. Mark the measurements and cut the appropriate trim pieces.
You should then attach the treads to the top of the wall and to the ceiling. After attaching the treads, you should assemble and attach the shiplap boards to the wall. Finally, you should attach the remaining trim pieces around the top and bottom of the shiplap boards.
This will complete the trim finish in shiplap.
What kind of molding do you use with shiplap?
When installing shiplap, the type of molding used will depend on the desired look and design. Commonly used types of molding include crown molding, wall panel molding, baseboard molding, batten molding, and chair rail molding.
Crown molding is generally used at the top most point of the wall or ceiling, where the two surfaces meet, to add a decorative touch. Wall panel molding, or wainscoting, can add an extra dimension to the walls by providing texture, color, and pattern.
Baseboard molding can be used to hide any gaps between the shiplap and the wall, and to provide an aesthetic transition from the wall to the floor. Batten molding can either be inset between shiplap boards, or it could be overlaid to add depth and dimension to the wall.
Lastly, chair rail molding can be used to define different areas on shiplap walls, adding a rustic aesthetic.
Do you cover nail holes in shiplap?
Yes, you can cover nail holes in shiplap. Depending on the size of the hole, you can use multiple methods to cover it. For small holes, you can fill them in with caulk, wood filler or putty. If the holes are larger, you have a few more options.
You can use a small piece of shiplap cut to size and secured with wood glue, or use a wood dowel. For an even more seamless look, you can use a wood trim piece which is fitted around the hole. As you are covering up the nail holes, be sure to match the paint or stain on the shiplap to ensure a consistent look.
What should I put behind shiplap?
Shiplap is an increasingly popular type of wall cladding typically consisting of wide boards installed in a horizontal overlapping pattern. It can be used to create an eye-catching, rustic look in any space in your home.
It is important to consider what you’ll be putting behind the shiplap to ensure that the cladding is secure and looks pleasant.
One way to ensure the best support for the shiplap is to install plywood sheets behind it. Plywood is strong, sturdy and perfect for creating a strong foundation for the shiplap to hang from. When you’re fastening the boards to the studs through the plywood you can also hang backing so that it covers the plywood and adds an additional layer of support.
This will also allow you to attach fixtures such as light fixtures as well as heavy objects such as wall art that could directly fasten to the plywood.
If you’re looking for a more lightweight option for behind the shiplap then you can use drywall instead of plywood. Drywall can be cut to the same size as the shiplap, providing some basic support but is not as strong as plywood.
If you go this route it is important to use removable anchors to ensure the shiplap is securely attached to the wall.
Regardless of what option you ultimately decide to use behind the shiplap, make sure to check the weight, measurements and installation instructions carefully. That way, you can be sure your shiplap will be securely fastened and look great for years to come.
How do you shiplap with baseboards?
Shiplapping with baseboards is a great way to create a classic, timeless look in any room. To achieve this look, start by ripping down the existing baseboard, keeping the installation height the same.
Once the baseboard is removed, use shiplap to line up and fit boards from floor to ceiling along the wall.
The next step is to attach each board to the wall. For best results, pre-drill each board and use nails to ensure that the boards are securely fastened. After the shiplap is installed, use a miter saw to cut the boards at baseboard height so they fit perfectly.
Once that’s complete, you can begin installing the baseboard. To do this, use a nail gun and nails to attach the baseboard to the wall.
Once the baseboard is installed, you can add the finishing touches. This could include caulking and painting or staining the boards to complete the look. And there you have it, you’ve successfully shiplapped with baseboards!.
Should I start shiplap from top or bottom?
That depends on the area where you want to install the shiplap. For example, if you are installing shiplap on a wall, you should always start from the top and work your way down. This will ensure that all of the seams between each plank line up, and it will create a consistent look.
If you are installing shiplap on a ceiling, then you should start from the bottom and work your way up. Again, this will ensure that the planks line up perfectly when they are installed. It may take a little more time to install the shiplap this way, but the results will be worth it.
Regardless of where you are installing the shiplap, make sure to use a level and a measuring tape to make sure that each plank is correctly placed before you secure it in place.
How do you get shiplap to meet in corners?
To get shiplap to meet in corners, you will need to make some cuts to your pieces, as the boards will not fit perfectly together in the corner without being cut. Before making any cuts, decide which board will be the corner board, as this will most likely require the most detail.
Start by measuring the corner and adding together the total width of the two shiplap boards that will meet in the corner. For greater accuracy, it can be helpful to set up a square using the corner as the 90-degree angle.
Once you have your measurement, subtract 1/8 inch to ensure a snug fit and make a mark on the corner board.
Using a circular saw or jigsaw, cut along the marked line. Make sure to support the board so it does not break as you cut. You will now have an angled cut along the full length of the corner board. Place the corner board into the corner, and the opposite board will now have a longer cut on the top, so subtract 1/8 inch from your total width measurement and make a mark on the opposite board.
Using a circular saw or jigsaw, cut along the marked line. Make sure to support the board so it does not break as you cut.
Place the board in the corner, and use a finish nail gun to secure them into place. A pneumatic nail gun will require a compressor, and this is available to rent. Alternatively, you can use a hammer and finish nails to secure the pieces together.
Use painter’s caulk along the edges and corners where two pieces of shiplap meet. The caulk will help fill any gaps and give an even, clean finish when painted.
How high should shiplap be on wall?
When installing shiplap on a wall, the general rule of thumb is to hang it approximately ⅝ of an inch off of the floor. This leaves enough space to hide any imperfections that may be present in the flooring, as well as to ensure that the boards are level.
The boards should be centered on the wall studs, and this will help to ensure that the boards will stay straight and level. Depending on the desired look, the shiplap can be hung anywhere from a few inches up to the ceiling.
If desired, a chair rail could also be installed to separate the shiplap into two distinct sections. For a more traditional look, start the boards approximately 32 to 36 inches off of the floor and stagger them.
This will create a more interesting visual effect and add visual depth to the wall. However, if you want to draw attention to the height of a room, running the shiplap from the floor to ceiling will create a more dramatic look.
Will shiplap warp in a bathroom?
Yes, shiplap can warp in a bathroom, just like any other type of wood. Moisture can be a big culprit when it comes to warping, so bathrooms are prone to this potential issue with shiplap. To help reduce the chances of warping, make sure the shiplap is sealed before installing it and consider investing in water-resistant shiplap or using a waterproof covering like painting or polyurethane.
Ideally, use a product specifically intended for wet areas. Additionally, keep the bathroom well-ventilated to reduce the amount of moisture in the air and utilize a dehumidifier if needed. Regularly apply sealant to combat any potential warping due to moisture buildup.
Lastly, inspect the shiplap regularly in order to catch any signs of warping early.
How do you prepare shiplap for painting?
Preparing shiplap for painting is a simple process. Begin by cleaning the wood with warm, soapy water and a sponge or cloth. If you are painting over an existing color, use a liquid sandpaper or sanding block to scuff up the surface.
This will help the paint adhere better to the wood. Once you have cleaned and lightly sanded the surface, make sure to remove any dust and dirt with a damp cloth.
For the best results, apply a coat of primer before you paint. Depending on the type of paint or varnish you are using, you may need to wait for the primer to dry (typically about an hour) before you begin painting.
It is important to only use paint that is specially recommended for use on wood such as shiplap. Ensure that you use a good quality brush and stir the paint well before using.
To ensure even coverage, begin at the top and work your way down, applying the paint in long, even strokes. Allow the first coat to dry before applying a second coat if necessary. Once the paint is completely dry, apply a thin coat of varnish to protect the wood if desired.