No, the Predator 3500 generator does not have an electric start. It does, however, have a recoil start system. The recoil start system allows you to turn the generator on and off with a simple pull of the cord.
Additionally, it has a low-oil shutoff that will automatically shut off the generator once the oil level reaches a critical level. Furthermore, the Predator 3500 generator has several other features that make it suitable for a variety of applications.
It has a maximum wattage output of 3,500 watts and a running wattage of 3,100 watts. It has two AC 120V outlets and one 12V DC outlet for charging batteries. Furthermore, it has an overload protection circuit for your devices and appliances.
Finally, the Predator 3500 generator has a fuel tank capacity of 4 gallons and a run time of around 10.5 hours at half load capacity.
How do you use the electric start on predator generator?
Using the electric start on the Predator generator is relatively simple. The first step is to make sure the generator is in a safe, well-ventilated area, has fuel and oil, and the power switch is off.
After these conditions are met, you can proceed with starting the generator.
To start the electric start Predator generator, begin by pushing the primer button several times until fuel begins to flow out of the primer bulb to the carburetor. Once the primer bulb is pressed, turn the power switch to the “on” position and check that the circuit breaker is up.
Now, press the “start” button on the generator control panel and hold it for 2-5 seconds until the machine begins to run. Once the engine is running, release the start button and let the machine run for at least 5 minutes to warm up and if the engine dies or falters simply turn the power switch back off, then back on and repeat the start process.
For additional safety, you can plug the power cord into an ground fault circuit interrupter (GFCI) before plugging it into an outlet. This important procedure should always be completed when starting any generator to help protect against electric shock should any problems arise during the operation of the generator.
Can predator generator get wet?
No, it is not recommended to get a predator generator wet. It is important to keep the generator away from water, as this can cause significant damage to the electrical components and may even lead to the generator malfunctioning.
It is also important to keep it free from any rust or corrosion. Additionally, moisture can create problems when it comes to the spark plugs and other parts that are vital for the generator to operate properly.
In general, it is best to avoid exposing the predator generator to any water, even if it is just a small amount.
What kind of gas does a predator 3500 generator take?
The Predator 3500 Generator takes regular unleaded gasoline with an octane rating of 87 or higher. The maximum tank capacity of the generator is 6.5 gallons, and it has an operating time of up to twelve hours on a single tank of fuel at 50% load.
When refueling the generator, make sure to turn it off and let it cool for about 15 minutes to prevent a possible fire caused by gasoline vapors. Additionally, the generator’s owner’s manual recommends adding fuel stabilizers to the gasoline to promote efficient and long-term storage.
How long will a 3500 watt generator run on a tank of gas?
The answer depends on a variety of factors, including how large the gas tank is, the load that is applied to the generator, and the fuel efficiency of the generator. Assuming a 20-gallon gas tank, a 3500 watt generator typically has an estimated run time of 8-10 hours at a 50% load with a fuel efficiency of 0.
25 gallons per hour. At full load, this run time can be reduced to 5-6 hours. When running smaller loads, the run time can be extended significantly. It’s important to remember that this is just an estimate, and run times could vary quite a bit depending on the exact model of the generator and the condition of the engine.
How many gallons of gas does a predator 3500 hold?
The exact capacity of the gas tank on a Predator 3500 generator depends on the specific model. Generally, most Predator 3500 generators have a 4 gallon tank capacity. This capacity allows for approximately 8 hours of running time with a full tank of gas at half load.
However, it is important to note that any other additional load can decrease the running time. Additionally, different Predator 3500 models may have slightly smaller or larger gas tank capacities as well.
For reference, other Predator models such as the 4000 watt generators typically have a 6.6 gallon tank.
Can you put a remote start on a generator?
Yes, you can put a remote start on a generator. A remote start allows you to start a generator from a distance without having to physically go to the generator. Depending on the type of generator you have, you can use different methods to install a remote start.
The most common type of generator remote start is a wireless unit that connects directly to the generator’s control panel and sends out a radio-frequency signal when you press the start button. Other systems may require professional installation and require you to remove the existing control board to add the remote start components.
If your generator is a portable unit, you may also need to buy a separate kit that includes a wireless receiver, transmitter and all necessary wiring. If you’re not sure what type of remote start to purchase, it’s always best to consult a professional.
How does a generator start automatically?
A generator can start automatically by connecting it to an automatic transfer switch (ATS). The transfer switch is a device that senses a power failure and will switch the power supply from the utility grid to the generator.
Once the utility power is restored, the transfer switch will switch the power back to the utility grid from the generator. This helps automate the process of starting the generator so that it can provide continuous power when utility power is lost.
Additionally, some generators may come equipped with a start/stop switch as well as a separate automatic control panel. This will help start and stop the generator as needed without having to manually reconnect and disconnect the generator to the transfer switch.
Can I convert a pull start to electric start?
Yes, you can convert a pull start to electric start. However, depending on the make and model of the vehicle, it may require you to make changes to its spark plug and flywheel, both of which may require special tools.
Furthermore, the battery you will need to install must be appropriately sized and able to carry the load of the engine as well. In addition, you will need to purchase a starter motor and solenoid, which will also need to be compatible with your vehicle.
Lastly, you may need to install a starter button and keyed switch, as well as wiring the new starter system. It is important to note that making this conversion can be a time consuming and complex task, and it is recommended that you enlist the help of a qualified mechanic or electrician.