Finding the model of your Craftsman chainsaw typically involves looking for the model number, which is usually located either on the starter handle or the crankcase. It can also be located on the barcode label, the product tag near the pull starter, or near the air filter.
Once you have located the model number, you can use the Craftsman Chainsaw Model Locator on the Craftsman website to determine the model. To use it, enter the Craftsman model number in the specified field and select the “Find Model” button.
The website will then display the model, type, and serial numbers of your Craftsman chainsaw.
How can I tell what year my Craftsman chainsaw is?
The best way to tell what year your Craftsman chainsaw is is to look at the serial number. Your serial number should be based on a date code which designates when the product was manufactured. To look up the date for your serial number, visit the Craftsman website, and go to their “Where is my Serial Number” page.
On this page, you can enter in your serial number and find out when your device was made. Additionally, you may be able to tell the year by looking at the design of your chainsaw, as well as any additional engine or blade components.
Where is the serial number on a chainsaw?
The serial number on a chainsaw is usually located on the side of the saw, usually near the motor. On some models, it may be stamped into the metal around the motor area. On others, it may be located on a metal tag on the motor housing.
If it is not immediately visible, check the owners manual for the exact location. It is very important to keep track of the serial number when purchasing a chainsaw, as it is useful if the chainsaw needs to be serviced or if you ever need to make a claim for warranty coverage.
How do you read a chainsaw chain number?
Reading a chainsaw chain number is quite easy if you know what to look for. Firstly, the chain number can usually be found stamped on the side of the chainsaw chain. This chain number will usually include three figures, such as the pitch size, chain gauge and the number of drive links.
The pitch size is the size of the bar and is usually the first number in the chain number sequence. Common pitch sizes are either 0.325 or 0.375 inches.
The chain gauge is the second figure and indicates the thickness of the drive links. Common chain gauges include .050, .058 or .063 inches.
The number of drive links is the third and final number in the chain number sequence and indicates the total number of drive links on the chain. If you count the number of drive links from one end of the chain and add one, you will have the number of drive links for the chain.
Once you have these three figures, you can easily read a chainsaw chain number and make sure that you have the correct chain for your saw.
Do Craftsman tools have serial numbers?
Yes, Craftsman tools do have serial numbers. The serial number is printed on the back of the tool near the handle. This serial number is usually around eight digits long and is typically divided by hyphens or spaces.
The serial number is a very important piece of information that can be used to identify the date and source of your Craftsman tool. This is useful for pinpointing when and where your tool was originally purchased.
Using the serial number can also help you to determine if your tool is covered under any warranty and can be used to check for recalls. Having the serial number of your Craftsman tool is a great way to ensure that you have the best possible guarantee of service and quality when using your Craftsman tools.
What model is my McCulloch chainsaw?
The specific model of your McCulloch Chainsaw is typically located on the starter cover. You should be able to find the model name or number on a small label or sticker. If you cannot locate the label or sticker, you may be able to find the information on the fuel tank, air filter box, or recoil starter.
Some McCulloch chainsaws feature the model name or number on the starter handle, or etched onto the side of the powerhead on the fuel tank side. In addition, you can try using online tools such as the McCulloch Chainsaw Part Finder, which can provide you with the model name or number based on the model type, type of fuel, fuel tank volume, and engine capacity.
If you have any more questions, feel free to contact your local McCulloch authorized service center for assistance.
What does the C mean on Stihl chainsaws?
The letter “C” on Stihl chainsaws stands for the chain type. In particular, the “C” stands for the Chain Type 3 controls, which are the latest development of Stihl chainsaws. This chain type is characterized by a special sprocket and control lever design.
The sprocket is constructed in a way that creates more rotation and traction when the saw is in use. Additionally, the control lever has a smooth plastic cap that will help to minimize the saw’s vibration.
This chain type is typically more expensive than other chain types on the market, but is also more efficient and smoother in operation.
How do you start a Craftsman gas chainsaw?
To start a Craftsman gas chainsaw, you’ll need to make sure that you have some safety gear on. This includes safety goggles, a hard hat, ear protection, and heavy-duty gloves. Once you have all of this in place, you can begin starting the chainsaw.
1. Locate the on/off switch to the right of the handle. Make sure that it is set to the “off” position.
2. Turn the fuel valve located at the rear of the saw to the “on” position.
3. Turn the choke valve to the “on” position, which is usually located near the on-off switch or choke button near the handle.
4. Pull the recoil starter handle approximately eight times to prime the engine.
5. Push the choke valve to the “off” position.
6. Push the throttle or trigger that is located near the handle and pull the starter handle rapidly. The engine should start up after a few pulls.
7. Once the engine is running, push the throttle all the way to the “full open” position. This will allow the saw to run at full capacity and be ready to use.
Finally, make sure you keep your safety equipment on at all times when using the chainsaw. Also, be sure to pay attention to any safety instructions, warnings, and/or symbols that may be printed on the saw.
Following these steps will help keep you safe while operating your Craftsman gas chainsaw.
How do you start a chainsaw that’s been sitting for years?
Starting a chainsaw after it has been sitting for years can be a complicated process. It is important to follow the manufacturer’s instructions in the owner’s manual carefully to ensure that you don’t damage your chainsaw or cause injury.
Before attempting to start the chainsaw, the first thing to do is to perform a thorough inspection to check the condition of the chainsaw. Check the fuel lines, fuel tank, and carburetor for any cracks or physical damage.
Also check the spark plugs, air filter, and the chain for any signs of wear and tear. Replace these parts if needed.
If your chainsaw has a primer bulb, make sure that that is working properly and free from any blockages. Make sure the fuel tank is full before you attempt to start the chainsaw. If the tank is empty, mix the appropriate ratio of oil and gas and fill the tank.
The next step is to make sure the choke is in the correct position. Depending on your model of chainsaw, you may have manual or automatic chokes. Once the choke is set, pull it a few times to get fuel into the system.
If your chainsaw has a decompression valve, depress it to help the engine turn over more quickly. Finally, firmly pull the starter cord on the chainsaw until the engine starts.
Following these steps should help you start your chainsaw after it has been sitting for years.
How do I start my chainsaw for the first time?
Starting a chainsaw for the first time can be a little intimidating, but it doesn’t have to be. Make sure that you take the necessary safety precautions before beginning.
1. Start by checking the chain tension. Make sure that it is tight enough but not too tight.
2. Thoroughly clean the exterior of your chainsaw. Make sure there is no dirt, dust, grease, or debris on the tool. This will help keep the saw running smoothly.
3. Fill the tank with the proper grade of gasoline and oil mixture (check your user manual for the ratio). For best results, use only fuel that has been purchased within the last 30 days.
4. Plug in your spark plug (if your chainsaw requires one).
5. Pull the recoil starter four or five times. This will get the engine to turn over and prime it before you attempt to start it.
6. Pull the choke lever out and hold it in place.
7. Squeeze the throttle trigger and pull the starter rope. Do not let go of the choke lever as you do this.
8. When the engine starts up, gradually push the choke lever in until it clicks into the open position.
With a little practice you will soon be an expert at starting your chainsaw. Take your time and work safely.
Why can’t I get my chainsaw started?
There are a variety of reasons why you may not be able to get your chainsaw started. The most common reasons that a chainsaw will not start are due to poor fuel flow, dirty air filters, stale fuel, debris in the carburetor, or worn ignition systems.
It’s important to first check that the power cord or battery is connected correctly, and that it is supplying the appropriate voltage to the machine. If the power cord or battery is not functioning, the chainsaw will not start.
Next, check the fuel. You should ensure that the tank is full and that the fuel is fresh. Stale fuel will prevent the engine from starting, as it has fewer combustible components. Dirt, water, or debris in the fuel can also clog the carburetor jets, and reduce the amount of fuel delivered to the engine.
Additionally, if the fuel lines have become blocked, or restricted, the engine may not be able to draw the fuel into the engine.
Lastly, ensure that the air filter is in good condition. Over time, air filters will become clogged with debris, and when this happens, the engine cannot receive the adequate amount of oxygen it needs to start.
Inspect the system, and if needed, replace the filter.
If after inspecting all these components, the chainsaw is still not starting, you may need to replace certain ignition components, such as spark plug, ignition coil, or flywheel key.
If these steps fail to start your chainsaw, then the problem might be bigger, and the best course of action would be to contact a professional for assistance and advice.
What are the 4 steps to starting a chainsaw on the ground?
The four steps for starting a chainsaw on the ground are as follows:
1. Gather the necessary safety gear. This includes protective goggles, hearing protection, and heavy-duty gloves.
2. Place the chainsaw on a level surface, such as the ground. Ensure that the saw’s brake is engaged and that the chain is fully stopped.
3. Prime the saw. Make sure the fuel tank is full and the choke control is in the “closed” position. Then, pull the primer bulb a few times to introduce fuel into the system.
4. Pull the starting cord. Typically, a couple of strong pulls are necessary to start the chainsaw. Be sure to move the choke control to the “open” position after the engine starts. After the saw has been running for a few minutes, gradually accelerate the engine and engage the chain brake to adjust the speed.
Should you drop start a chainsaw?
No, you should never drop start a chainsaw. If a chainsaw doesn’t start right away, do not attempt to drop start it in an effort to get it to start, as this can cause serious injuries to both the operator and bystanders.
Before starting the chainsaw, ensure that the chain brake is engaged, the chain is in good condition, the air filter is clean, the fuel tank is full, and the spark plug is in good condition. If, after all of these checks, the chainsaw still won’t start, then take the chainsaw to a professional for further inspection and maintenance.
How long to wait if chainsaw is flooded?
If your chainsaw is flooded, it is important to wait at least 15 minutes before attempting to restart it. This allows the fuel to dissipate and give the motor enough time to cool down. It is also important to ensure that all of the fuel has been drained from the carburetor before attempting to start it again.
To do this, detach the fuel line from the carburetor and allow the gas to completely drain out. Once any fuel remaining in the carburetor has been emptied, reattach the fuel line and try to start the chainsaw again.
If the chainsaw does not start, check for other common issues such as an clogged air filter or spark plug wire. If these components are in good working order, it may be time to consult a professional.
Should you start a chainsaw with the chain brake on?
No, you should never start a chainsaw with the chain brake on. The chainsaw’s chain brake is designed to stop the spinning of the chain to help prevent the accidental start of the chainsaw. When the brake is on, it puts pressure on the chain and can affect the performance of the engine.
If you start the chainsaw with the brake on, it can cause too much strain on the engine and can possibly lead to damage of the chainsaw. Additionally, starting the chainsaw with the brake on can reduce the speed of the engine and make it harder to start.
Therefore, you should always check to make sure the brake is off before you start the chainsaw.