To get all the water out of your Intex pool, you will need to first turn off any power to the pool and drain the water using a submersible pump. Place the submersible pump at the lowest point in the Intex pool and attach a garden hose to the pump’s outlet.
Create a sloping landscape away from the pool allowing the water to flow out using gravity. Next, use pressure from the pump to push the remaining water out. This will require you to run the pump until there is no more water coming out.
Lastly, make sure to check the pool for any additional water and manually remove any that is left. It is important to remember to always disconnect any power source before operating any draining equipment.
Additionally, it is important to ensure that the area where the drained water will be flowing is not going to cause any flooding or temporary drainage issues.
How do I drain my 18 ft Intex pool?
Draining an 18 ft Intex pool can be a fairly straightforward process, depending on how much water needs to be removed.
1. Start by purchasing either a submersible water pump or a sump pump designed for pools, whichever works best for your particular pool.
2. Place the pump in the deepest area of the pool and make sure it is securely in place.
3. Connect a hose to the pump, preferably one that is reinforced and reinforced nylon that can withstand water pressure. Make sure to secure the hose to the pump.
4. Position the free end of the hose outside the pool at a low location. If you have a lawn or something similar outside the pool, the water can be drained there.
5. Turn on the pump, and once it’s turned on, the pool should start to drain. It may take a few hours or even days depending on how much water needs to be drained.
6. Monitor the pool while it’s draining, and if necessary, re-position the hose if it starts to clog up with debris.
7. Turn off the pump when the pool is empty and disconnect the hose. Once the pool has been drained, you can begin to clean it and prepare it for whatever activity you will be doing next.
What is the fastest way to empty an above ground pool?
The fastest way to empty an above ground pool is to use a submersible pump. This device uses suction and an electrical motor to remove large quantities of water in a short amount of time. Ideally, the pump should be connected to a garden hose that leads away from the pool and to an area where the drained water can be safely diverted.
Before turning on the pump, you should also make sure that the hose is securely in place and free of any objects that could clog the pump or block the flow of water. Once the pump is set up and turned on, it should be able to empty the pool in just a few hours.
It is important to note that the suction power of a submersible pump will depend on the depth of the water in the pool. For this reason, it may be necessary to use a ladder to reach the lower levels of the pool and to manually scoop out any water that is too low for the pump to reach.
Additionally, it is also important to turn off the pump after a few minutes of use to ensure that it does not overheat. If it is too hot, you may need to wait about 15 minutes for it to cool down before resuming.
How do I drain my Intex pool without the adapter?
If you want to drain an Intex pool without using the adapter, the most common solution is to use a submersible pump. It will be connected to a garden hose and simply used to draw the water out. It’s important to note that the pump needs to be powerful enough to move the water quickly and safely.
Ensure that the garden hose is run downhill or to a sufficient drain that won’t be overwhelmed by the quantity of water you are draining from the pool. Another option would be to find a nearby pool service representative who could come and drain your pool for you.
This would be more expensive but much more convenient.
How long does it take to drain a pool with a garden hose?
The amount of time it takes to drain a pool with a garden hose depends on several factors, including the size of the pool, the length of the hose, water pressure, and the amount of water in the pool.
Generally, to empty a standard-size pool with a standard-size garden hose, you should expect to spend three to four hours. However, if you have a standard-size pool, a long hose and increased water pressure, it may take anywhere from two to three hours.
If you have a smaller pool and a short hose, it may take as little as one hour. On the other hand, emptying a larger pool can take anywhere from five to seven hours.
How do you siphon water out of a pool with a hose?
To siphon water out of a pool with a hose, you will need a long hose with a large enough diameter to fit over the pool’s suction drain. Begin by placing one end of the hose into a bucket or container.
Make sure the hose is long enough to reach from the pool’s suction drain to the bucket. Next, open the valve on the suction drain to begin the siphoning process. Once the valve has been opened, you can begin stirring the water at the opposite end of the hose from the bucket.
This stirring motion will create a vacuum, which will then pull water up and out of the pool and into the container. Once you have successfully created a vacuum, you can close the valve on the suction drain.
This will allow the vacuum to remain in the hose and the water to continue draining until the bucket is full or the desired amount has been removed. It is important to note that the container must be placed lower than the suction drain in order to allow the siphoning process to take place.
How can I empty my pool without a pump?
Emptying a pool without a pump requires a bit of extra effort, as a pump can be used to make the process more efficient. However, it is still possible to empty your pool without a pump.
One method is to mop the pool with a wet/dry shop vac. Fill up the vac with the pool water, then empty it into another larger container such as a kiddie pool, and then dump the contents into a drain or outdoor area.
This process can be very time consuming and requires a lot of manual labour, but it is an effective method if you don’t have access to a pump.
You can also transfer the water into a garden hose using a siphon. This method works similarly to the shop vac, except instead of using a vacuum, you use a garden hose to suck up the pool water. This can also be done with a few buckets and a bit of elbow grease.
Finally, you can rent or purchase a submersible pump. These pumps are specifically designed for removing water and are much faster than hand-pumping methods. They can be attached to a garden hose and will easily move the water from the pool to the desired location.
No matter which method you choose, it is important to remember that safety is the top priority. Make sure to have the right safety equipment and inspect the pool area prior to performing any draining activities.
Can you use Intex pool without pump?
No, you cannot use an Intex pool without a pump. The pump of an Intex pool is used to both circulate the water and filter debris. Without a pump, the pool would become a stagnant body of water that could quickly become contaminated and hazardous.
Without a pump to keep the water circulating, the pool chemicals may not be evenly distributed throughout the pool water and could cause an imbalance. Additionally, algae and other contaminants would be allowed to grow unchecked without the filter of a pump.
This could make the pool unhealthy to swim in and would also require a considerable amount of time and effort to clean.
Can I drain pool water on lawn?
Yes, draining pool water in your lawn is generally safe, but it is important to do it correctly. First, test the water to make sure it is suitable for being used as lawn irrigation–it should have a pH between 6.5 and 8.
If it is, then you can slowly drain your pool by clipping the hose to the pool drain at the end nearest the pool and into a grassy area furthest away from the pool. Ensure that the hose is clamped securely and make sure the end not in the pool is higher than the other end so that the water doesn’t run back into the pool.
Finally, be sure to check your local laws and ordinances regarding dumping pool water onto your lawn before you get started.
Do you have to drain Intex pools for winter?
No, you do not have to drain Intex pools for winter. The Intex pool company suggests that you should winterize your pool and not drain it. This means lowering the water level a few inches below the skimmers and putting non-toxic pool antifreeze in skimmers, return lines, and any other areas of possible water freeze.
Additionally, you should add pool winterizing chemicals to reduce the water’s alkalinity and chlorine levels, cover your pool with a winter cover, and clear out debris such as leaves and dirt from the bottom of the pool.
This will protect your pool from the harsh winter elements and make it easier to reopen in the spring.
Can you leave Intex pools up all year?
No, Intex pools should not be left up all year. While the pool itself is made of a strong, durable material, it is not designed to be kept up for a long period of time, as the material can become brittle due to prolonged exposure to the elements, causing cracks and other damage.
Additionally, it is important to properly winterize an Intex pool, which includes taking down the walls and storing all pool equipment. This will help minimize the potential for damage to the pool walls and liner.
Additionally, it is recommended that the pool remain empty throughout the winter months to help prevent ice damage to the pool. If you leave the pool up and filled, stress from the weight of the water can cause damage to the liner, walls or support structure of the pool.
Can you drain an Intex pool?
Yes, you can drain an Intex pool. Intex pools use a drain plug at the base of the pool’s wall that can be used to drain the water. To drain the pool, you’ll need a garden hose that will be connected to the drain plug.
You must also remove any filter cartridges from the filter cartridge intake before draining the pool. The pool water should then be directed away from the house and any hard surfaces. It can be drained into the lawn or flowerbeds, or preferably a storm drain.
Make sure to check with your local municipality for any rules on draining swimming pools. Additionally, please make sure to not drain the pool onto a neighbor’s property. It is important to also never drain water from a pool onto a street or sidewalk, as this is illegal in most cities.
Once the pool has been drained, you may need to remove any algae, dirt, and debris before refilling your pool.