Removing UniFi devices depends upon the specific model and generation of the device, as well as what type of device it is. For most UniFi devices, the removal process is relatively straightforward and can be done quickly.
Typically the first step is to physically disconnect the device from the network – simply unplugging the cable or power source from the device. If the device is a wireless access point, it’s important to check that it’s disconnected from any Wi-Fi networks as well.
Once the device is physically disconnected, the next step is to log into the UniFi controller software. This is the web interface through which all UniFi network devices are configured, and it’s the best way to remove a device.
To do this, the user needs to open a web browser on the computer that is connected to the network and enter the IP address of the UniFi controller. The default IP address is often 192.168.1.30 although this may vary depending on how the controller is configured.
Once logged in with the appropriate credentials, the user can navigate to the device list, select the device to be removed, and click the delete button.
If the UniFi device is an older model or is not connected to the network, another method may be necessary. In these cases, the user can access the device’s local configuration page directly by entering the device’s IP address in the browser.
This will bring up an interface from which the device can be removed or factory reset. In either case, the device will be removed from the network, allowing the user to add any new or replacement devices.
How do I change the default website in UniFi controller?
To change the default website in UniFi controller, you must first make sure that UniFi controller is running and that your device is connected to the same network as the controller. Once you have verified this, then you can start the process of changing the default website.
First log into the controller with your username and password. After that, go to Settings > Networks in the left-hand panel. Once you are here, select the site from the list that you want to change.
Then, select the Edit option from the top-right corner to edit the network settings. Select the DHCP Name Server and change the value to your preferred website. After you have selected the changes and saved them, you will have now successfully changed the default website in UniFi controller.
How do I uninstall UniFi controller from MAC?
The process for uninstalling the UniFi controller from a Mac is relatively straightforward.
First, you should locate the UniFi controller application in the Applications folder on your Mac. Once you have located it, you should drag the application to the Trash.
The next step is to remove the controller configuration files. To do this, navigate to ~/Library/Application Support/ and remove the Unifi folder. Then navigate to ~/Library/Preferences and delete the com. ubnt.
Unifi. plist file.
Once these steps have been completed, the Unifi controller has officially been uninstalled from your Mac. However, you may want to perform additional cleanup depending on your needs. This includes removing back up copies of the controller configuration, deleting controller logs, and if you are using the automatic backup feature offered by the Unifi controller, you may want to delete the backup files stored in the ~/Library/Application Support/Unifi/backup folder.
How do I transfer UniFi AP from one site to another?
The process of transferring a UniFi AP from one site to another can be completed in a few simple steps.
First, you will need to physically move the UniFi AP from the old site to the new site. Make sure to power down the AP and disconnect all the network cables before uninstalling it from the old location.
Next, you need to set up and configure the new site for your UniFi AP. Configure the Wi-Fi router and make sure the correct UniFi controller software is installed. Then, connect all the necessary cables, such as the power, Ethernet cables, and Wi-Fi antennas, to their respective ports.
Once the new site is configured, you can reinstall the UniFi AP to the new location. Connect the power, Ethernet cables, and Wi-Fi antennas, and then power the AP on. The controller should be able to detect and adopt the AP.
You can then use the UniFi controller to monitor and adjust the settings of the AP as needed.
It is also important to note that it is best to factory reset the AP before transferring it. This will ensure that the AP is not configured with any of the settings from the old site. To factory reset the AP, you will need to hold down the reset button for at least 10 seconds until the LED light starts to blink rapidly.
Overall, transferring a UniFi AP from one site to another is a relatively straightforward process that can be completed in a few steps. Physically move the AP from the old site to the new site and set up the new location.
Then, reinstall the AP and configure it with the new settings as needed. Finally, make sure to factory reset the AP to ensure that any old settings are reset.
Can you mix UniFi APs?
Yes, you can mix different types of UniFi APs together, however it is important to make sure that your APs are on the same firmware version. The same SSID and security configuration should also be used across all of the UniFi APs to ensure the best user experience.
Depending on the type of network you are setting up, different types of UniFi APs may be beneficial when setting up the service. For example, if you are setting up a large network, using different types of long-range APs like the UniFi LR and UniFi SHD may be beneficial.
In addition, combining one or two indoor access points like the UniFi AC Pro, or a UniFi Mesh Access Point with a UniFi AP AC Outdoor is another good option for outdoor coverage. It is also crucial to keep in mind the number of users the network will support, and how the different types of APs will interact with each other to affect the overall performance.
How do I manually adopt UniFi?
If you are wanting to manually adopt a UniFi device, you will first need to make sure the device is plugged in to either the LAN port or PoE port of your controller. You then need to identify the local IP address of the device either through your router or the controller’s DHCP list.
Once you have located the local IP address, open the UniFi controller and go to the Devices tab. You will see your device in the “Pending Adoption” list, double click on it then enter the IP address you previously located on the previous step.
Follow the remaining on-screen instructions to finish the adoption process.
It’s also important to consider configuring your device. To do this, click on the device in the Unifi Controller and configure any changes such as changing the device name or setting a static IP address.
You can also adjust any settings related to wireless connections, traffic shaping, and more. Save your configuration once complete.
Once your device has been adopted and configured, it should show up in the Unifi Controller. You can now use the device to control and monitor your network.
Can Unifi controller be on a different subnet?
Yes, the Unifi controller can be on a different subnet. This is particularly useful if you have multiple networks within the same physical environment, or if you want to allow access to the controller from remote locations.
For example, if you wish to manage a network at a branch or remote office, you can configure the controller to be on a different subnet and then connect to it securely over the internet.
In order to configure the controller to be on a different subnet, you’ll need to connect the unique IP address assigned to the controller over the internet. You’ll need to set up a static route on the router to ensure that the traffic from the controller can reach the other subnet.
Once that is configured, you should be able to access the controller from the remote location.
It is important to note that any device that you want to manage with the controller, such as a Ubiquiti access point, will need to be configured for the correct IP range for the controller. If any of the devices are configured for the wrong IP range, the controller will not be able to communicate with them.
How do I adopt an Unifi AP by IP?
Adopting an Unifi Access Point (AP) by IP address is a straightforward process, but it is important to make sure you have the right network settings and credentials on hand first. First, you will need to make sure you have enabled DHCP (e. g.
on a wireless router or gateway) so that the AP has an IP address it can use to connect. Secondly, you will need to make sure the AP is in the same subnet as the DHCP server, so the AP knows where to look for the DHCP server.
Finally, you will need to configure the Unifi AP with the relevant credentials and setting details, including the IP address, subnet mask, gateway, DNS server, username and password for the network.
Once the above is set up, you can connect your computer to the Unifi AP via an Ethernet cable. Make sure your computer is using the same subnet as the AP and enter the IP address of the AP in your web browser.
This should open the Unifi Controller web interface. From here, you will be able to adopt the Unifi AP by entering the Shared Secret Key and clicking Adopt. Once the adoption process is complete, you will be able to configure and manage the AP via the web interface.
How do I adopt a UniFi security gateway to an existing network?
To adopt a UniFi Security Gateway (USG) to an existing network, there are four main steps you’ll need to follow. First, you need to physically install the USG on the network by connecting the router to the modem and other network devices.
Then, you need to configure it in the UniFi Controller software. This is done by adding the USG device to the UniFi Controller, setting the correct IP address, gateway, and subnet mask, and then configuring the DHCP server settings.
After that, you’ll need to update the firmware. This can be done automatically from the UniFi Controller, or you can use SSH to do it manually. Finally, you’ll need to link the USG to the other UniFi devices connected to the network.
To do this, you must “adopt” the USG into the existing network by clicking the “Adopt” button in the devices’ settings. After that, the USG should be successfully added to your existing network.
What is the Web address for UniFi controller?
The web address for the UniFi controller varies depending on the device that you are using. If you are using a PC or Mac, the address will be http://localhost:8443. If you are using an iOS or Android device, the address will be http://unifi:8080.
If you are using a web browser, then the URL will vary according to your ISP (Internet Service Provider). Some ISPs may use http://unifi. companyname. com or http://unifi. home. net or http://unifi. example. com.
It is recommended to contact your ISP to find out the exact URL for your UniFi controller. Once you have obtained the URL, you will be able to access your UniFi controller.
What is the default database name for UniFi?
The default database name for UniFi is ‘unifi’. This database is a MongoDB database used to store all of the network data for the UniFi network. It contains information about the access points, the users that connect to the network, and all of the various settings for the network.
The database is stored locally on the controller’s system and can be accessed from Command Line Interface.
What database does UniFi controller use?
The UniFi Controller software uses MongoDB as its database system. MongoDB is a NoSQL database system, meaning it does not store its data in a traditional row-and-column table format. Instead, MongoDB stores its data in a collection of JSON documents, which makes it ideal for storing and querying large amounts of unstructured data.
The UniFi Controller software also makes use of MongoDB’s distributed approach, allowing data to be spread across multiple servers for better scalability. This makes the UniFi Controller software extremely reliable and fast, even when dealing with large amounts of data.
Where are UniFi controller settings stored?
The UniFi controller settings are stored in a database located on the device running the UniFi Network Controller software. This device can either be a dedicated server/computer, or a cloud-hosted remote service such as the UniFi Cloud Key (available from Ubiquiti).
When running the UniFi Network Controller software on a computer, the data will be stored in a local .SQLite database file, typically located in the data/ directory of the application.
On a UniFi Cloud Key or a dedicated server or computer, the database file is located in the /srv/unifi/ directory (depending on your installation). The database files are named “unifi. db” and “unifi_stat. db”.
The UniFi controller stores all the information about the current state of the network, including the settings for the access points, networks, and other network details. It also stores historical data such as traffic logs, permission settings, and other relevant information. The unifi.
db stores this data, while the unifi_stat. db stores data related to statistics and performance of the network.
Where is the UniFi database?
The UniFi database is an embedded databases used to store data for the UniFi Network Controller. It is located in the system’s user folder in a file named “unifi. db”. On Mac OS, the UniFi database is located in the ~/Library/Application Support/UniFi folder.
On Windows, the database is located in the %USERPROFILE%\Ubiquiti Unifi folder. It is recommended to keep a backup of the database since it may become corrupted or deleted. It is also recommended to keep the database on a protected drive or in a secure location since it holds sensitive information.
If the database is deleted or corrupted, the UniFi Network Controller must be completely restarted.
How do I find my access database name?
To find your access database name, the easiest way is to open the database in the Access program. Once it is open, look at the title of the opened window at the top or look in the left corner at the bottom to see the file name – this will be the Access database name.
You can also look in the File menu and select File Info to find the database name and other information about the file. If you are using a version of Access prior to 2000, you will also find the database name in the Tools menu > Options > Advanced.