To reset your Pentair Intelliflo pump:
1) Unplug the power/connector cord from the side of the motor.
2) Activate the reset button (located on the motor) by pushing it in with a small screwdriver.
3) Plug the power/connector cord back in.
4) The pump will now begin its initial starting sequence, which includes all pumps running for period of time and then shutting down.
5) Once the initial starting sequence is complete, the pump is now reset and ready to use.
How do you program a Pentair Intelliflo variable speed pump?
Programming a Pentair Intelliflo variable speed pump involves following several steps. The first step is to perform a check-up of the connections. Ensure all electrical connections are properly made, and check if the pump is receiving power.
The next step is to program the pump using the packaged controller, which can be done using a switch or by downloading the Pentair mobile application. With the switch, you will need to select the voltage, switch between single and dual speed, set up the run hours, and configure the priming function.
With the mobile app, select the control setup then you can edit existing settings or create a new profile. The main parameters to be set are the speed, required flow rate, priming, run hours and monitoring.
After programming the pump, do a final check to ensure the settings are correct and all is functioning properly.
How do you unlock Pentair pool pump?
To unlock a Pentair pool pump, you will first have to locate the pool control box. The box should be located on the outside of your home near the area of the pool. Once you have located the control box, open it and look for the circuit breaker that controls the pool pump.
Flip the breaker to the off position and wait for 10 to 15 minutes for it to cool down. After the designated time, flip the breaker back on and the pool pump should be unlocked. If the pump fails to unlock, then you may have a problem with the pump or the wiring.
In this case, it is best to contact a qualified pool service technician.
How do I set the clock on my Pentair easy touch?
Setting the clock on the Pentair easy touch is relatively simple. You will first need to locate the main control panel, which is usually found in the pool equipment pad. Once you have located the main control panel, open the lid and press the center button to enter the main menu.
From the main menu, scroll until you find the time settings, which is usually the first option. Once you have opened the time setting menu, press the plus or minus buttons to adjust the hours and minutes.
When you are done, press the center button to save your changes and exit the menu. To finish up, close the main panel lid and the clock should be set.
How do I reset my priming alarm Pentair?
Resetting your priming alarm on the Pentair pump requires a few simple steps. First, shut off the power to the pump and remove any debris or clogs from the pump housing. After that, check the pump’s suction strainer to make sure it is clear and not clogged.
Next, open the Pentair’s Air Release Valve, located on the pressure gauge, and let some of the air escape. Once the pressure has equalized, reset the priming pump by pressing the red priming button on the motor and holding until the pump begins to prime.
If the pump does not begin to prime, you can check the Priming Puddle in the priming housing to make sure it is full. If the pump still does not prime, you may need to open the pump and inspect the impeller and/or motor to ensure it is in good condition.
Lastly, replace the filter and check the pump and priming alarm settings to make sure they are set correctly. Once all steps have been successfully completed, your Pentair pump should reset and be ready to use.
What is an overcurrent alarm?
An overcurrent alarm is a device or system designed to detect and alert of an electrical current that is higher than the rated level of the circuit. It is usually triggered when the current exceeds a specified threshold known as the overcurrent limiting value.
This value can be predetermined by the manufacturer or adjusted according to the application. Depending on the design, an overcurrent alarm may be used to simply alert of the overcurrent situation or to actively shut off the power supply.
When an overcurrent alarm is triggered, it sends a signal to the user. This signal can be used to warn of potential danger or to shut off the power supply. The alarm is usually integrated into the electrical system and can detect an overloaded circuit before it causes damage.
This can protect against potentially hazardous situations. Overcurrent alarms are often used in industrial and commercial applications as part of a complete safety system.
In addition to overcurrent alarms, electrical systems can be protected by installing circuit breakers. These are specially designed switches that will automatically shut off the power supply in the event of an overcurrent condition.
While the alarm is an effective way of warning users, circuit breakers are the only way to ensure the current is cut off. It is important that the circuit breaker is rated to handle the load of current in the system.
What speed should I run my Pentair pool pump?
It is important to note that the ideal speed of your Pentair pool pump generally depends on the size, shape, and volume of your pool, as well as the type of filter you have installed and the number of water features you are running from the pump.
A good rule of thumb is that you should be running your pump for about 8 to 12 hours per day, at a speed that will allow your filter to turn the entire volume of pool water over approximately once per day.
To calculate this speed for your pool, divide the volume (in gallons) of your pool by the total number of hours you plan to run your pump per day. The result should be the gallon per minute (GPM) flow rate you should aim for when setting the speed of your Pentair pool pump.
It is important to keep in mind that relying too heavily on a general recommendation, versus doing the calculations to find that Works best for your pool, may result in your pump running at the wrong speed.
This can lead to improper filtration, poor circulation, and, eventually, pool water problems. Therefore, it’s best to take the time to calculate the ideal speed for your pool pump.
Additionally, if you’re ever in doubt, you can find further guidance on setting your pool pump speed in the product manual that came with your Pentair pool pump. If a manual was not included, you can request one directly from Pentair.
How do I start my pool pump after winter?
If you’re getting ready to start your pool pump after a winter of inactivity, there are a few steps you’ll want to take first. Before you start the pump, you should check that all the electrical components of the pump are in good working order.
Make sure the electrical cords are properly connected and are in good condition. Additionally, check the inside of the pump for any evidence of rust or corrosion which could potentially damage the pump.
Next, evaluate the motor itself for any signs of damage or wear. Make sure the impeller is securely attached. Inspect the surrounding seals, lubricants, and other components to make sure they are in working order.
If there is any damage or issues, you will need to take the appropriate measures to repair them before starting the pump.
Once you have inspected and repaired the pump, you’ll need to prime the pump. This is done by manually filling the pump’s priming chamber with a bucket of water. This ensures that the pump is completely filled with water before running and prevents damage to the pump.
Now that you have checked, repaired, and primed the pump, you can start it up. Make sure you have access to an emergency shut off switch in case the pump needs to be immediately turned off. Start the pump at a low speed and then gradually turn up the speed until it reaches the recommended operating speed.
Let the pump run for at least 15 minutes before turning it off. And finally, check all connections and components to make sure that everything is running smoothly.
Why will my pool pump not turn on?
One potential issue could be a power supply or circuit breaker issue. If the circuit breaker controlling the pump has been tripped or there is an interruption in the power supply, then the pump will not be able to turn on.
You might need to locate the circuit breaker and reset it, or contact your power supplier to find out if they are having any issues with your electrical connection. A second possible cause may be a clogged or blocked impeller, which is the part that helps drive the water circulation within a pump.
If there are any obstructions preventing the impeller from operating properly, then the pump may not turn on. You may need to disassemble the pump to access and clean the impeller. Finally, if the pump has been in operation for a while and been subjected to rusting or corrosion then it could lead to the motor burning out.
In this instance, you would need to completely replace the pool pump motor.