Taking off an OtterBox case is fairly easy. To begin, locate the seam located at the top and bottom of the case. Gently grasp either side of the tab, then pull away from the device to release. If the case feels too tight, use a flathead screwdriver to gently pry the edges of the case apart.
Once it is open, disconnect the power button and volume switch if applicable. Carefully rock the device out of the larger lower portion of the case. With the device free, grasp the remaining sides of the case and remove.
How do you remove the plastic cover from an OtterBox Defender?
To remove the plastic cover from an OtterBox Defender, start by removing the inner tray from the plastic shell and setting that aside. To remove the plastic shell from the rubber shell, use something like a flathead screwdriver or table knife to insert into the groove along the top edge between the two and separate them.
You can then remove the plastic shell. Finally, use a pair of scissors or a sharp knife to carefully cut the three plastic posts and remove the plastic cover. Be sure to cut close to the posts and be careful not to damage any other components of your OtterBox Defender.
Once all three posts are cut, you can pull the plastic cover away and discard it.
How do I remove my OtterBox case from my Samsung?
Removing an OtterBox case from a Samsung device can be done by starting with the top corner of the case and slowly, but firmly, pulling it away from the device. You may have to wiggle the case a bit as you pull it in order to loosen the grip of the case.
Then, do the same for the bottom corner, again firmly, but slowly, pulling it away until the case is totally separated from the device. Make sure that all sides of the case are completely removed from the device, since an OtterBox case may also have a tight fit around the sides of the device.
Additionally, try lifting away the inner case as you pull off the outer case as the inner case may create a seal around the device. Lastly, take care and avoid any jerking motions in order to avoid causing any damage to the device.
How do I get my phone out of OtterBox Defender?
To remove your phone from your OtterBox Defender, first, remove the clip from the back of the case. You will find it near the top. Then, from the sides, carefully pop out the inner shell, which holds the phone in place.
Once the inner shell is removed, your phone should slide out easily. Be careful that you don’t drop the inner shell when you remove it, as it will be fairly snug in the Defender’s outer shell. Once you have your phone out, put the inner shell and clip in a safe place so that you can reassemble the Defender when you need to.
How do you remove an OtterBox Defender from an iPhone 13 Pro Max?
Removing an OtterBox Defender from an iPhone 13 Pro Max requires a few steps to ensure that both your phone and case stay safe during the removal process. Begin by gently pushing the volume button away from the phone to separate the two pieces of the OtterBox Defender.
Next, insert the thumbnail of a fingernail into the small crack between the phone and the case on any corner of the phone. Gently pull the fingernail along the corner to separate the plastic pieces and find the middle of the case.
Once the plastic pieces of the defender case are separated, continue to use the thumbnail to remove the defender case from the iPhone 13 Pro Max. When removing the plastic pieces, make sure that you don’t pull too hard as this can damage both the phone and the case.
Lastly, gently pull the phone away from the plastic pieces of the OtterBox Defender. Once the phone is free, complete the removal of the case by carefully lifting the plastic pieces away from the iPhone 13 Pro Max.
With the OtterBox Defender successfully removed from the phone, your iPhone 13 Pro Max is now ready for any new cases you may choose.
Do you need a screen protector with Otterbox Commuter?
Yes, it is always a good idea to use a screen protector when using any phone case, including an Otterbox Commuter. A screen protector will help protect the display of your device from scratches and other types of damage.
It’s especially important to use a protector if you plan on taking your device outdoors. Most Otterbox cases come with a built-in screen protector, but if you are looking for an extra layer of protection, you can purchase a separate screen protector that is compatible with an Otterbox Commuter.
Screen protectors can be very affordable and will provide your device with an extra layer of protection against the elements.
How do you put on the Otterbox symmetry defender Commuter case?
Putting on the Otterbox Symmetry Defender Commuter Case is quick and easy. First, start off by taking the front and back pieces of the case out of packaging. Then, align the ports and buttons on the back piece with the device, ensuring the device fits comfortably inside.
Next, snap the back piece onto the device. After that, take the front piece of the case, line it up along the screen, and press down all the edges. Lastly, push down firmly, making sure the case is securely attached on all sides.
What is the difference between Otterbox Defender commuter and symmetry for iPhone 11?
The Otterbox Defender Series and Symmetry Series are two of the most protective cases available for the iPhone 11. The main difference between these two series is that the Defender offers greater protection and durability while the Symmetry line is a bit thinner and provides a more modern, stylish look.
The Otterbox Defender Series offers total protection with a triple-layer construction that consists of a rigid internal shell to absorb impacts, a built-in screen protector to guard against scratches and a durable outer slipcover.
This case also offers port covers that keep dirt, dust, and lint from getting inside.
By contrast, the Otterbox Symmetry Series offers slim design with a single-layer construction, a built-in scratch protector, and a slim profile with a light and thin feel. While it offers some drop protection, it doesn’t offer the same level of coverage as the Defender.
The Symmetry series is perfect for those who want sleek protection without giving up on style.
Overall, the Defender Series is ideal for those looking for maximum protection and durability while the Symmetry Series is best for those looking for lightweight protection with a modern, stylish look.
Can you remove the built in screen protector on the Otterbox Defender?
Yes, the Otterbox Defender does come with a built-in screen protector, but you can remove it if you would prefer not to have it. To do this, you’ll first want to release the snap connections that are located just above the headphone port and along the left and right side of the case.
Thoroughly examine the inner linings of the phone case to make sure all the snap connections are released. Additionally, you may need to use a small flathead screwdriver in order to get the snaps open.
Once the snap connections are opened, you can slowly lift off the inner shell of the Otterbox Defender and the screen protector should come off with it. Be careful to make sure you don’t damage any of the parts in the process.
If you decide that you want the screen protector back on the case, you can simply reverse the above steps and snap the inner lining of the phone case back into place.
Does Otterbox Defender have a built in screen protector?
No, Otterbox Defender does not have a built in screen protector. Instead, the case provides robust protection against shocks, drops, dust, and even water damage. The case has a three-part construction, consisting of a two-piece polycarbonate shell, a built-in screen protector guard and a hi-impact polycarbonate slide on shell.
The screen protector guard helps protect your device against scratches, dust, dirt and miscellaneous debris, while the hi-impact polycarbonate shell provides extra support to the corners and edges of the device for increased protection against drop and impacts.
Additionally, the case features a belt clip holster for easy portability.