To change the line on a Husqvarna 128ld trimmer, you will need to follow these steps:
1. Switch off the trimmer and disconnect the spark plug wire from the spark plug.
2. Remove the cutting head from the unit by pressing the head and rotating it counterclockwise.
3. Remove the cover from the cutting head, followed by the spool inside the head.
4. Unspool the existing line from around the spool, and discard it.
5. Insert the new line into the spool. Make sure the line is equal distances from the inlets or grooves available inside the spool.
6. Place the spool back inside the head, making sure that the line feeds correctly before closing the head.
7. Reinsert the head onto the unit and rotate it clockwise until it locks in place.
8. Reconnect the spark plug wire to the spark plug and you’re ready to use the trimmer.
How do you string a Husqvarna?
Stringing a Husqvarna lawn mower or string trimmer is a relatively simple process that requires only a few steps. First, remove the flywheel cover and spark plug from the unit. This will ensure that the engine is safe to work on.
Once the cover and spark plug are removed, locate the starter rope. Unwind it from the flywheel and prepare for threading the new string. Then, use a pair of needle nose pliers to open the spool, and begin feeding the string through the spool in a clockwise direction.
Wind the string up halfway and move onto the next step. After that, locate the retainer clip and remove it to release the end of the string. Place the clip onto the open end of the string, and thread the starter rope through the newly installed string.
Then, wind the string a few more turns, and stretch it out to ensure the tension is uniform. Finally, tie a knot, reattach the flywheel cover, and spark plug. The Husqvarna lawn mower or trimmer should now be properly strung and ready for use.
How do you replace trimmer line?
Replacing the trimmer line in a trimmer is a fairly simple process. First, you’ll need to disconnect the spark plug wire and ensure the trimmer is off. Then, depending on the type of trimmer you have, you will either have to remove the head of the trimmer or loosen the spool.
Cut the old line, if present, with scissors or a knife. Then, measure out a length of replacement trimmer line. The length of trimmer line needed will depend on the size of the trimmer head, but it is usually between 10 and 15 feet.
Next, you will need to measure the correct sized line for your trimmer head. This will be mentioned in the trimmer’s manual or can usually be found by examining the trimmer head itself. Once the length and diameter of the line have been determined, you can cut the line to that length and thread it through the hole in the trimmer head.
Finally, you will attach the ends of the new line to the spool and replace the head or spool back on the trimmer.
How do you put a brush cutter blade on a Husqvarna?
Putting a brush cutter blade on a Husqvarna is a relatively straightforward process. First, make sure the spark plug end is facing away from you so that the blade can spin freely. Next, put the blade onto the brush cutter shaft along with any washers necessary.
Following this, secure the blade by tightening the bolt and lock nut combination, making sure both are tight. Finally, check the blade’s security and make sure it is firmly attached. Occasionally the blade may come loose during use, so be sure to check it periodically and retighten if necessary.
What does a choke do on a trimmer?
A choke on a trimmer helps to provide a richer fuel mixture when starting the unit and helps to prevent over-priming. Chokes are generally fixed devices that are used to restrict airflow for a richer fuel mixture.
This enriched mixture helps the piston to combust fuel more efficiently to start the engine. It is generally recommended to move the choke lever or knob to the “closed” position when starting the trimmer, and then move it back to the “open” (or off) position once the engine has started.
Some models may have an automatic choke that will automatically open or close at specific times. It is important to understand the specific instructions for your trimmer model and follow it accordingly.
How do you fix a trimmer that won’t start?
If your trimmer won’t start, there are a few things you can do to try and fix it.
First, check the spark plug and see if it needs cleaning. Dirty spark plugs can prevent your trimmer from starting. Clean or replace the spark plug, depending on the condition.
If the spark plug isn’t to blame, the next thing to check is the air filter. If the air filter is dirty or clogged, it can restrict the airflow to the carburetor and prevent your trimmer from starting.
Replace the air filter if it is dirty.
It might also help to clean the carburetor. This can help clear away gunk that may have accrued over time, which can usually be done by spraying a carburetor cleaner into the carburetor opening.
Another thing to check is the fuel filter. Clogging of this filter can make it harder for the fuel to get to the combustion chamber. If the fuel filter is clogged, replace it with a new one.
Lastly, you should check the pull starter. Make sure it is in good condition and that it is not damaged or worn out. If it is damaged or worn, replace it with a new one.
Following these steps should help you troubleshoot and fix your trimmer if it is not starting. You can also consider taking it to a professional if it still doesn’t work.
Why did my trimmer stop working?
There could be several potential causes for your trimmer to stop working; from a loose wire to a faulty motor. It is important to first identify the problem before attempting any repairs yourself.
First, you should check for any indicators of external damage such as a broken spark plug, damaged carburetor, or clogged air intake. If these are all in good condition, you should move on to inspecting the internal components.
Pay special attention to any loose wires and connections. Check the voltage output of the spark plug and the general health of the spark contact points. If everything here looks fine, it could be a problem with the ignition coil, flywheel, or even the trimmer motor itself.
If the trimmer continues to not work, it is best to reach out to a certified technician or service center who can diagnose and repair the device as quickly and safely as possible. This will help you avoid more complicated and costly repairs, and help you get your trimmer back in proper working order.
How do I fix my lawn trimmer?
If you are having trouble with your lawn trimmer, there are a few steps you can take to attempt to fix the problem before bringing it to a repair shop. First, inspect the spark plug. Check that it is in proper working order and is not damaged.
If there is a problem with the spark plug, it can be replaced with a new one.
The second step is to check the fuel line. Inspect the fuel line to ensure that it is free of blockages. Clear away any debris that you find and replace it if it is damaged.
Once you have checked the spark plug and fuel line, it is time to inspect the air filter. Make sure the filter is clean and free of dirt and debris. Replace it if necessary.
Finally, check that all of the connections are secure and the cables are in good condition. Bent, cracked, or frayed cables should be replaced.
Once all of these steps have been completed, you should start the trimmer and see if it works. If the problem is still not solved then you may need to take the trimmer to a repair shop for further inspection.
What do the choke symbols mean?
The choke symbols in electrical diagrams represent a coil or transformer that is used to control the current flow in the circuit. It is often used as a filter or to limit the current to a certain level so that it does not damage the other components in the circuit.
The symbol is usually represented by two concentric circles with the inner circle being larger than the outer circle. The choke symbol can be seen in many electrical devices such as radios, computers, and televisions.
The choke is often used to reduce noise or interference in these devices. In other applications, the choke symbol is used to represent a voltage regulator that keeps a steady voltage in the circuit.
Can I use string trimmer to edge?
Yes, you can use a string trimmer to edge. A string trimmer is a handheld, motorized garden tool that is used to trim grass, weeds, and other foliage where your mower cannot reach. The trimmer is equipped with a rotating cutting head at one end, with a long cutting line for trimming grass and weeds, and a plastic or metal guard to protect the user from the spinning line.
When used for edging, the string trimmer head is positioned vertically so that the line is driven along the edges of the lawn, cutting grass and weeds that have grown too long. When making an edge, the line should be kept just above the surface of the ground, but be sure not to cut too low as it can damage the surface.
Make sure to use an appropriately powered string trimmer that is designed for edging. It is also important to maintain the string trimmer to ensure it is running in its optimal state, as the line can quickly wear down when cutting through tough foliage.
Is Husqvarna 128LD commercial grade?
No, the Husqvarna 128LD is not a commercial grade product. It is designed as a homeowner/occasional use gas-powered trimmer. This means it can handle some light/occasional yard work, but it is not designed to handle the demands of consistent and demanding commercial applications.
If you are looking for a commercial grade option, the Husqvarna range offers a variety of models designed specifically for commercial applications. These come with higher power engines, upgraded corrosion-resistant construction and heavy-duty components which were designed to handle the demands of more frequent and extended use.
What is the difference between Husqvarna 128LD and 128LDX?
The Husqvarna 128LD and 128LDX are both string trimmers designed for home use. The main difference between them is in the power of the engine. The 128LD has an engine with a power output of 28cc, while the 128LDX has a slightly more powerful engine with an output of 29cc.
Additionally, the 128LDX includes an advanced starting system featuring an air purge and Smart Start technology, which makes it easier to start the engine. Both models are equipped with a trimmer head and a Tap ‘n Go dual-line cutting system, allowing users to quickly and easily replace the line as it wears down.
Finally, the 128LD includes a T25 bump feed trimmer head while the 128LDX includes an Auto Feed trimmer head, which automatically feeds the line as needed with a simple tap on the ground.
How long does Husqvarna 128LD last?
The expected lifespan of the Husqvarna 128LD depend on how it is used, maintenance and other related factors. Generally, the average life expectancy of this trimmer is between three to five years. Though, it is important to note, with regular maintenance and proper storage, this trimmer can last up to a decade or more.
To extend the life of the 128LD, it is essential to properly use and store the trimmer. This includes cleaning the trimmer after each use, properly winterizing and replacing worn and damaged parts. Additionally, carefully following the instruction manual can ensure proper maintenance and usage of the trimmer to extend its life.
How many cc’s is a Husqvarna 128LD?
The Husqvarna 128LD is a lightweight gas-powered trimmer that has a 28cc 2-cycle engine. This two-stroke engine is designed to run on a combination of gasoline and two-stroke oil, providing an optimal balance of power, performance, and reliability.
With its lightweight design and straightforward starter system, the Husqvarna 128LD makes tackling tough trimming jobs easy and efficient. The lightweight design, combined with its powerful 28cc two-stroke engine, make the Husqvarna 128LD a reliable and efficient trimmer.
Its easy to use starter system can get the job done quickly, while still delivering the power and performance required to take on any task. Additionally, the trimmer has an adjustable handle and smart guard system, making it easy to customize the user experience.
In total, the Husqvarna 128LD is a 28cc 2-cycle engine trimmer, making it an ideal choice for trimming and edging your landscaping.
Where are Husqvarna brush cutters made?
Husqvarna brush cutters are primarily made in Husqvarna’s factories located in Europe, US and Brazil for the North America market, as well as its factories located in China for the Asia Pacific market.
This ensures that Husqvarna has the capacity and capabilities to meet the ever-increasing demand from its customers, while maintaining high standards of quality and efficiency.
Many Husqvarna brush cutter designs are designed specifically for local markets, and Husqvarna works closely with its local partners to make sure it can supply the best possible products for its customers across the globe.
Several of Husqvarna’s North American purchasing contracts are with suppliers that maintain manufacturing facilities in the US and Canada.
In addition, Husqvarna draws on its extensive, international network of foundry and fabrication service providers located in different countries that supply it with premium grade castings, mill rolls, components and fasteners.
This ensures that the firm is able to access the latest advances in technology and methods to fulfill its customers’ needs in all parts of the world.
What size string does Husqvarna use?
Husqvarna uses a range of string size options depending on the model of trimmer. Generally, the sizes include 0.095-inch, 0.105-inch, and 0.115-inch diameter trimmer line. The heavier gauges are recommended for larger areas, thicker vegetation, and heavier weeds, while the smaller gauges are best for small, delicate gardens, and around flower beds where precision is key.
Husqvarna also carries an array of trimmer heads to accommodate a variety of sizes and shapes of trimmer line for different applications. If you are ever unsure of what size is best for your model, a Husqvarna authorized dealer will be able to provide you with detail for the specific model.
How much power does a 25cc engine have?
A 25cc engine has about 1.1 horsepower (HP). This is a small amount of power compared to the power of other, larger engines like gasoline engines in cars. However, for small motorized applications like string trimmers, leaf blowers and chainsaws, a 25cc engine is usually sufficient for powering the equipment.
Outdoor power equipment with 25cc engines typically has a speed of 6,000 to 9,000 RPM (revolutions per minute) and can generate up to approximately 2.1 foot-pounds of torque. Depending on the type of outdoor power equipment, this power output can be enough to get the job done.