In order to clean the drain pump filter on a Maytag front load washer, you’ll need to locate the filter, which is situated at the front of the washer near the bottom. First, unplug the washer and shut off the water supply.
Next, tilt the washer back, resting it against a wall or something secure to hold it in place. Place a towel under the machine to catch any water that may spill. Locate the filter access panel and remove it.
On some models, the filter will be inside; on others, the filter will be accessible through the access panel.
To remove the filter, grab the tab at its center and pull outwards. It may be stuck due to debris or accumulated lint, so use some force if necessary to unscrew it. Once it’s removed, pull the filter out.
Inspect it for dirt and debris. If necessary, rinse off the filter and use a soft brush to clean out any hidden dirt.
Replace the filter, lining up the arrow with the grooves in the housing so you don’t cross any threads. Make sure that the filter is secure before re-installing the access panel. Finally, turn the water supply back on and plug the machine in.
Your Maytag front load washer should now be ready for use.
Where is the filter on my front load washing machine?
The filter on a front load washing machine is typically located either inside the washing machine drum or near the bottom of the front of the washing machine. On some models, the filter may be pointed downwards so that it can be accessed through a small hatch near the bottom of the machine.
To access the filter, open the hatch or unclip the access panel on the front of the machine and locate the filter. Once located, you may need to unscrew the filter or detach it from its housing before removing it.
Once removed, be sure to check for any blockages, debris, or foreign objects that may be lodged in the filter. After cleaning the filter, be sure to place it back in its housing and reattach the access panel or securely close the hatch.
Where is the drain filter on a Maytag washer?
The drain filter on a Maytag washer can usually be found on the lower front panel of the washer. It is typically located in the right-hand corner of the panel. On the left side, there is usually a large access panel that needs to be removed.
This may require a Phillips head screwdriver. Once the access panel is removed, the drain filter should be exposed and clearly visible. It will likely be a small cylindrical filter with a handle attached to it.
It can be accessed and removed for cleaning or replacement. Make sure to always consult the manufacturer’s user manual for specific instructions and warnings before attempting to work on any type of appliance.
Do Maytag washers have filters that need to be cleaned?
Yes, Maytag washers have filters that need to be cleaned. This is important to do on a regular basis as a clogged filter may cause the washer to perform poorly while using more energy than normal. In some models the filter may be located behind the lower access panel, while on other models it can be found inside the water pump.
It is typically a small cylinder-like device that can be easily removed and cleaned. The filter can become clogged with lint, fibers and other particles that build up over time. It’s best to check the user manual of your Maytag washer for exact instructions for cleaning the filter.
It’s a good idea to clean the filter of your Maytag washer at least once every 6 months or more frequently if you use it frequently or if you wash items with a lot of lint or pet hair.
Where is my Maytag water filter located?
Your Maytag water filter is typically located inside the refrigerator. It will be in either the top right or top left corner of the interior compartment, behind the grille with a label that reads “Water Filter.
” Depending on the model of refrigerator, you may also find the filter at the back or on the bottom. To access the filter, open the grille, release the filter from the locking mechanism, and twist counterclockwise to remove it.
After replacing the filter, be sure to reset the indicator light to indicate that the filter has been changed.
Does top load washer have drain filter?
Yes, most top load washers come with a drain filter. This filter is located at the bottom of the washer and can be accessed by removing the selector knob. The drain filter catches lint, pet hair, and other debris that accumulates in the washer.
Over time, the filter can become clogged with dirt and other debris, making it difficult for the washer to drain properly. To prevent this from happening, the filter should be cleaned regularly. This is easily done by running water over the filter and then gently pushing the dirt and debris from the mesh of the filter.
How do I remove the filter from my Maytag washer?
Removing the filter from a Maytag washer is fairly simple. Depending on the model you have, you may be able to access the filter from the back of the washer. If this is the case, you will need to unplug the washer from the electrical outlet, take off the back access panel, and then locate the filter.
Once located, you can use a flathead screwdriver to remove the clips holding the filter in place and then remove it. If you do not have access to the filter from the back of the washer, you will need to remove the top of it and then locate the filter.
To do this you will need to lift the top of the washer and then unplug the lid switch wires. Once the lid switch wires are disconnected, you will be able to remove the entire lid from the washer and then locate the filter.
Again, use a flathead screwdriver to remove the clips to take out the filter. Once the filter is removed, you can then put everything back together in the reverse order and plug your washer back in.
How do I know if my washing machine filter is clogged?
If your washing machine filter is clogged, it can cause various issues with the machine’s performance such as poor drainage, clothes not becoming as clean as they should, or even an unpleasant odor developing.
To determine if your washing machine filter is clogged, you can begin by checking the filter itself. Most modern washing machine models have a filter located behind the lower part of the kick plate at the front of the machine, but some will have it located on the side or rear.
Depending on the model, the filter will either be a simple hinged plastic flap, or screw-on lid that can be opened to reveal a lint filter and/or a small hose. If the filter is clogged with lint, debris, and/or small particles, simply use a pair of pliers to remove any blockages.
If the filter doesn’t appear to be clogged, then the issue likely lies elsewhere.
You should also check the hoses on the back of your washing machine for any signs of clogging such as kinks or pinched joins. Any kinks or pinched hoses should be straightened out using a pair of pliers.
It is also important to check the hoses for any signs of wear or tear, as these can lead to a clogged filter. If any of the hoses appear to be damaged, they should be replaced before continuing with the cleaning process.
Finally, you should use a camera with a long cable to inspect the inside of the washing machine. If you see any signs of a clog within the plumbing or drain, you should use a plunger to remove it. Alternatively, a plumber’s snake can be used to remove any debris that may be lodged in the drainage pipes.
In summary, to know if your washing machine filter is clogged, you should first check the filter itself for any signs of blockage. You should also check the hoses for any signs of wear or tear. Finally, use a camera and a set of tools to inspect the inside of the washing machine for any potential signs of a clog.
Will washing machine STOP IF filter is blocked?
Yes, if the filter in your washing machine is blocked it will likely stop the machine from functioning. The filter is designed to trap lint, hair, and other debris so it does not circulate through your washing machine and end up on your clothes.
If it gets clogged, it will interfere with the machine’s ability to properly fill with water, wash and spin your clothes. If this happens, the machine will most likely shut down completely. You should also be aware that if the filter is blocked, it can cause other components of the washing machine to become damaged.
In order to prevent this, it is important to regularly clean and check your washing machine’s filter to ensure it is free of any blockages.
What if my washer doesn’t have a filter?
If your washer does not have a filter, it is important to regularly check for lint or debris buildup in and around the washer. From time to time, you should check hoses for leaks and clean any residue from the hoses.
It is also important that you should not overload the washer and always use the appropriate detergent according to the care instructions of the items being washed. This can help prevent the build-up of residues that could clog up the washer.
Additionally, you should always follow the instructions in the user manual when operating your washer. This helps to ensure that your washer is working properly and that any potentially damaging problems are avoided.
Does every washer machine have a filter?
No, not all washing machines have filters. Most front-loading machines don’t have filters because the clothes go into a sealed drum. Top-loaders, however, typically have a filter near the bottom near the water pump that helps keep the washer clean by trapping lint and similar debris.
Some newer models also include filters for removing pet hair and other items from the washer. So, it depends on the type of washing machine.