Installing a roughed-in basement toilet can be done in six steps.
1. Determine the toilet location. Before you install a new toilet in your basement, it’s important to determine the proper location that won’t interfere with existing pipes or electrical lines. Toilets must also be at least 15 inches away from any wall.
2. Assemble the rough-in flange. Using the black ABS solvent cement, attach the rough-in flange to the supplied pipe and couplings. It’s important to wipe away any excess glue for a secure bond.
3. Install the supply line. Using copper tubing and copper fittings, run a cold-water supply from the main line to the toilet. Make sure to use a valve and a union, so that you can quickly access and shut off the water, should there be a problem.
4. Install the rubber seal over the flange. Make sure the seal is placed on the flange correctly so that a tight connection is made when the bowl is set on top.
5. Connect the bowl to the flange. Once the rubber seal is properly installed, carefully set the bowl onto the flange and secure it with the included bolts.
6. Test your connection. Turn the water back on and check for leaks. If any connections appear to be faulty, be sure to tighten them up or replace the gasket, as needed.
Once all the connections and seals are secure, it you can set the tank and bowl cover on the toilet and begin enjoying your new basement bathroom.
How do you replace a toilet flange in a basement?
Replacing a toilet flange in a basement can be an intimidating task, but it is a necessary fix when the flange becomes corroded or breaks. Knowing the installation process ahead of time can make the job easier.
1. Turn off the water supply. Before beginning any work on the toilet, make sure to turn off the water supply. This will prevent any accidental flooding while you are working on the flange.
2. Disconnect the flange. Depending on the type of flange, this can typically be done with a wrench.
3. Clean the piping. This step is essential to make sure the new flange will fit securely.
4. Apply a putty seal around the outside of the new flange. This seal will help prevent any leaks.
5.Set the new flange using a closet flange bolts. Make sure the bolts are placed into the slots of the flange and tightened securely to ensure a good seal.
6. Connect the toilet to the flange. Finally, it’s time to connect the toilet to the flange. Make sure all connections are secured tightly to avoid any leaks.
7. Turn the water supply back on. When the toilet has been securely connected to the flange, turn the water supply back on and flush the toilet to make sure the flange is working properly.
By following this guide, you can successfully replace the toilet flange in a basement. It is important to remember that when dealing with plumbing fixtures, it is always best to err on the side of caution and call a professional plumber if you are unsure of any part of the process.
How do you measure a 10 inch or 12-inch rough in for a toilet?
Measuring the rough-in for a toilet refers to determining the space between the wall behind the toilet and the center of the closet flange. To measure a 10 inch or 12 inch rough in, start by measuring the distance from the center of the closet flange to the wall behind it.
A 10 inch or 12 inch rough in is measured from the center of the flange, extending toward the wall. If your measurement is 10 inches or 12 inches, then you have a 10 inch or 12 inch rough in. If the measurement is different, then you have a different rough in size and must select a toilet accordingly.
It is important to know the size of the rough-in for your toilet as some toilets will only fit in certain sizes. If a toilet is not the correct size for the rough in found in a space, the flange will not line up correctly, potentially resulting in leaking and damage to the floor.
Therefore, it is essential to accurately measure the rough in size so that you can install the toilet correctly.
How far from wall should toilet drain be?
When installing a toilet, it’s important to keep the distance from from the toilet drain to the wall at least 12 inches. This is to ensure the waste can exit the drain properly and that the toilet can still be easily cleaned.
Some models of toilets may require more or less space, so be sure to follow the instructions provided by the toilet’s manufacturer before beginning installation. Additionally, it’s important to give proper thought to the location of the drain before installation.
If possible, the toilet should be installed in a location where the drain is able to tie into the home’s existing plumbing easily, but if the necessary location requires it to be closer to the wall, the toilet should be positioned so that the distance from the drain to the wall is as far as necessary to ensure proper clearance.
How much space is behind a 12 in rough in toilet?
The space behind a 12 in rough in toilet can vary depending on the type of model you have. In general, however, there will be at least 3 to 5 inches of space behind the toilet for your plumbing connections.
This would be the space between the back of the toilet and the wall. Depending on the model, there may be more than 3 to 5 inches of space, as some toilets come with an extended bowl or flange that can give you a bit extra space.
Make sure to measure carefully before you purchase a new toilet to ensure that the space behind the toilet is enough for the connections you need.
Why is my toilet so far from the wall?
The distance from the toilet to the wall is generally determined by the style of toilet that is installed in the space. Some toilet styles require a greater distance from the wall in order to function properly due to the angle of the flushing mechanism, plumbing connections, and water supply line.
Additionally, the distance from the toilet to the wall is necessary to ensure accessibility to the plumbing underneath. If the toilet were to be installed too close to the wall, it would be difficult to access the plumbing in order to repair or make adjustments to the fixture.
The distance also allows for the installation of features such as a recessed shelf, storage vanity, or towel bar behind the toilet. As such, the standard distance from the toilet to the wall is generally required by plumbing and building codes to ensure a safe, functional installation.
Should there be a gap between toilet and wall?
Yes, there should be a gap between a toilet and the wall. This is an important consideration when installing a toilet, and the gap serves an important purpose. The gap between the toilet and the wall allows for proper air circulation, which is essential for keeping the toilet clean, as it prevents the accumulation of moisture and bacteria around the base of the toilet.
This air circulation also helps to prevent issues such as odors and mildew from developing, which can lead to significant health hazards. In addition, having a gap between the toilet and the wall helps to reduce chances of the toilet becoming damaged due to a pressure build-up from behind the wall, which can occur from the toilet being too close to the wall.
Should a toilet be up against the wall?
Whether or not a toilet should be up against the wall depends on the bathroom design and the type of toilets being installed. In some cases, a toilet may need to be pushed back up against the wall to save space or because of plumbing limitations.
However, if a bathroom has sufficient space and allows for it, a toilet should not necessarily be placed up against the wall. When a toilet is spaced away from the wall, it often allows for easier access in the restroom and lends the space an open feel.
In the case of a wheeled and wall-mounted toilet, a bit of space between the wall and the toilet can make cleaning a lot easier. Ultimately, the best location for any toilet comes down to individual design preferences and space restrictions.
How is toilet rough in distance measured?
Toilet rough in distance refers to the measurement of the distance between the finished wall and the center of the closet flange. This dimension is important for toilet installations because it determines the type of toilet bowl and wax ring combination needed for a proper fit.
To measure the toilet rough in size, use a tape measure and measure from the finished wall straight through to the center of the closet flange. This should help provide an accurate measurement. The closet flange is the “ring” fitting at the bottom of the toilet.
It’s the part installed into the drain of the existing plumbing and usually has several bolts where the toilet bowl is attached. It’s a good idea to measure twice, as incorrect measurements can lead to a potentially serious installation problem.
Depending on the toilet rough in distance, you may need to purchase an offset flange to make a perfect fit during installation. The toilet rough in distance standard distance measurements are normally 12 inches, 10 inches or 14 inches.
How far does an offset toilet flange move?
The amount of movement that can be achieved with an offset toilet flange depends on the type of flange being used. Generally speaking, standard 3″ and 4″ offset flanges are designed to move the toilet about 1-1/4” to 1-1/2″ away from the wall.
Hinged offset flanges can move the toilet around 3-5/8″ from the wall and double offset flanges can provide up to 4-1/4″ of movement. It’s important to note that the distance specified is the total amount of movement the flange can provide.
If the goal is to move a toilet by 1″ away from the wall, a standard 3″ or 4″ offset flange can still be used, but one side of the toilet would need to be raised or lowered by the full amount of movement the flange provides (1-1/4” to 1-1/2″) to account for the lack of compensation on the other side of the toilet.