Measuring for a Roman shade is not as difficult as it may seem. The first step is to determine where on the wall you would like the shade to be installed. Measure the width and then add an additional two to four inches to ensure that the window is fully covered.
When measuring the height, measure from the top of the window frame to the top of the shade. You should also measure the distance from the top of the window frame to the desired bottom of the shade. Take these measurements and add a minimum of two inches to each to ensure that the shade fits properly.
Once you have your measurements, you can order your shade with the appropriate size. Most Roman shades have a fabric overlap, which is the fabric that hangs slightly over the side of the shade to give it a more finished look.
The overlap should be determined based on how much extra fabric is desired.
In addition to measuring the size of the shade, you need to make sure that you have the correct mounting hardware. If your window frame is deeper than one and one-half inch, you may need to purchase mounting hardware that is designed for deeper frames.
Follow the instructions carefully when installing the hardware and pay close attention to the specific measurements used. Finally, once the hardware is installed and your Roman shade is ready to be hung, you will need to attach the lift control clips and cords to the hardware.
Be sure that these are securely fastened and the cords are properly adjusted so that the shade operates smoothly.
Should roman shades be longer than window?
Yes, it is generally recommended for Roman shades to be longer than the window they are hung on. This is because when the blinds are open the fabric should extend beyond the window sill and onto the wall.
An appropriate size difference is usually around 4-6 inches, although this may vary depending on personal preference. When the blinds are closed they should also cover the window sill. Additionally, it is important to take into account the height of the window and the position of the cords or rods when measuring the length.
Too long of an overhang and the fabric may bunch up at the bottom of the window and look cluttered. If the windows are in a high traffic area, it is generally best to measure the blinds a bit longer to ensure they hang safely out of the way.
How are faux roman shades measured?
Measuring for faux roman shades is different than measuring for other window treatments. To ensure an accurate fit, measure the window opening at three different points: top, middle, and bottom. For a standard outside mount, measure the width of the window opening across the top, middle, and bottom to determine the full width of the shade.
Take the smallest measurement and round down in one-eighth inch increments. Next, measure the height of the opening from the top of the molding to the sill or bottom of the window. Choose the length of the shade based on where you’d like it to end.
For an inside mount, measure the inside width of the opening at three separate points (top, middle, and bottom). Choose the width of the shade based on the narrowest measurement, rounding down in one-eighth inch increments.
Finally, measure the inside height of the window opening. Choose the length of the shade based on where you’d like it to end. Remove 1/2 inch from the width measurement to ensure proper clearance of the faux roman shade.
When ordering, be sure to use the measurements in one-eighth inch increments, not in inches.
What if my roman shade is too long?
If your roman shade is too long, there are a few things you can do to fix it. First, you can gather the excess fabric at the top, and adjust the lift cords until it is the desired length. You can also remove the dowel and trim the bottom of the shade to the appropriate length, keeping in mind to leave at least a couple of inches to ensure the back of the shade is supported and remains flat.
Alternatively, you can use a ladder to reach the top of the window, undo the screws that hold the shade in place, and lower the eyelets so the fabric is higher. Again, you can trim the extra fabric from the bottom of the shade.
Finally, if you’re comfortable with a bit of sewing, you can also alter the head rail or hem of the fabric to make the shade shorter.
Is it OK for blinds to be longer than window?
Yes, it is ok for blinds to be longer than the window they are covering. Having blinds that are too short means that they won’t fully block out the light, while blinds that are too long can cause safety concerns as they may be a tripping hazard.
Measuring the window and selecting blinds that are slightly longer than the window ensures a secure and desirable fit. For large windows, having the blinds slightly wider than the window also helps to create a more balanced, symmetrical look.
How much longer should my blinds be than my window?
When deciding how much longer to make your blinds than your window, it is important to consider the space you have and the effect that you want to achieve. It is generally recommended to measure 1 – 3 inches beyond the size of the window, allowing enough space for the headrail and operational cords.
If you have a large window, then you may want to go for a longer blind. For example, if your window is 96” wide, it’s advisable to have a blind that is 99-106” wide for a standard single blind. If you are looking for a more modern and luxurious look, then having extra length can create the illusion of a larger window, or for a more formal look, you may opt for the same size blind as your window.
Ultimately, it is a matter of finding the best balance between style and practicality, so it is worth taking your timeu to measure carefully and make the decision that works best for you.
How much of the window should a roman shade cover?
When considering how much of the window a Roman shade should cover, it is important to take into account the shape, size, and style of your window, as well as the look and feel that you want to create in the space.
Generally, Roman shades should cover at least two-thirds of the window width. For example, a 36” wide window should be covered by a minimum 24” shade. When mounted outside the window frame, the shade can usually be as wide as the width of the window itself.
Alternatively, when mounted inside the window frame, there should be at least an inch of the window sill exposed on either side. The fullness of the shade should also be taken into consideration. If you want more privacy, use the fullness of your room to your advantage by having a shade that is slightly wider than the window and leaves only a small gap when lowered.
Conversely, if you want a more open look, you could consider having a smaller shade that would still cover just over two-thirds of the window when pulled down. As a general rule, lighter fabrics should have a slightly fuller shade than heavier fabrics, and variations in the style of shade can also affect the fullness measurements.
Where should Roman blinds sit?
Roman blinds are an attractive window covering option and can be fitted in any room. To achieve the look you want, they should be fitted correctly. Generally, they should sit just above the window frame, unless the window is wide and high.
In this case, they should be fitted to the ceiling. Roman blinds should never be fitted where they will obscure the view out of the window as this could create a hazardous living environment.
When measuring for the blinds it is important to consider the depth of the window frame as this will need to be taken into account when deciding where to fit the blinds. For example, if the window frame is large, the Roman blinds should sit higher up to create a more aesthetic look.
The position of the Roman blinds should also take into consideration any furniture that needs to pass underneath it. The fabric needs to be high enough not to be hindered, but still low enough to be an effective window covering.
In short, Roman blinds should be fitted depending on the size and depth of the window. Generally, they should sit just above the window frame, but wider and higher windows should be fitted to the ceiling or wall.
Roman blinds should never be fitted where they will impair the view out of the window, and consideration should be given to any furniture that requires to pass underneath.
Where should blinds be placed in recess?
When placing blinds in a recess, it is important to consider the size of the recess space and how much of the area will be covered by blinds. The industry standard for optimal coverage is that the blinds should reach all the way to the edges of the recess and slightly overlap them.
This creates a flush look and provides increased privacy and light-blocking benefits. If the size of the recess prevents the blinds from reaching all the way to the edge of the recess, consider purchasing a recess mount-kit or ordering blinds (or shades) with a wider size than the recess.
This will provide added coverage and a more aesthetically pleasing look. It is also important to ensure that the blinds are securely mounted to the wall in order to prevent them from slipping or becoming loose over time.
How do you calculate folds for Roman blinds?
There are few steps to calculate the correct size of the Roman blinds for the window. The measurements required are: window width, window depth, sill height and windows height.
1. First measure window width. This is the width of the window across the top. Measure the width of the window from one end to the other end, in centimeters. This is the width measurement needed for the blinds.
2. Measure the window depth. The depth measurement is from the inside of the casing of the window on one side to the other. Measure the depth in centimeters.
3. Measure the sill height. This is the height of the existing sill or the height that the new sill will be when it is installed in the window. Measure the sill height in centimeters.
4. Measure the window height. This is the height from the inside of the window casing on the top side to the inside of the casing on the bottom side. Measure the window height in centimeters.
Once you have the measurements, use the formula below to calculate the size of the Roman blinds that you need:
((window width + 3 cm) x (window depth + 9 cm)) + (window height x 2) + sill height = blind size.
The extra 3cm in the window width and 9cm in the window depth is the extra fabric that will be required to be able to fold the Roman blinds.
Therefore, once you have the measurements and you’ve calculated with the formula, you will know the total amount of fabric and the size of Roman blinds that you need in order to install it in the window.
How do Roman blinds look from outside?
Roman blinds from the outside provide a more contemporary and sophisticated look to any window they are installed on. They are distinct from regular roller or blackout blinds and offer various unique benefits.
Roman blinds are composed of a flat, fabric panel which pleats up evenly when raised and stretches down flush when lowered. When viewed from the outside, Roman blinds provide a smooth and eye-catching look.
When the blinds are completely lowered, they provide a seamless and elegant curved line across the window, with little to no fabric visible.
The look of Roman blinds from the outside can vary greatly, depending on the fabric and color used. Many fabrics offer unique colors and textures, ranging from patterned and sheer materials to velvet, linen and blackout options.
The colors of the fabric can also range from a neutral palette to vibrant colors, allowing for customization to the décor of the space.
Roman blinds are also designed for maximum practicality. Because the pleats stay firm when lowered, they block more light than other types of blinds, which can be ideal for bedrooms looking for extra privacy.
They are also relatively easy to clean, since most fabrics can simply be wiped with a mild cleaning solution. In addition, they can be easily adjusted with accompanying cords Weft they can provide good insulation from heat and cold, depending on the fabric used.
How much depth do you need for inside Mount roman shades?
The exact amount of depth needed for inside mount roman shades will depend on the size of the window and the type of shade you are installing. Inside mount roman shades typically require a minimum depth of 3 to 4 inches.
If the window depth is less than 3 inches, an outside mount should be used instead. Additionally, certain styles of shades like woven wood shades, pleated shades, or blackout shade may need a deeper window depth than standard flat roman shades.
If you are unsure about the specific requirements for your window, it’s best to consult with a window shade expert or manufacturer for more information.
Are Roman blinds dated?
Roman blinds have been popular for many years, and in some cases, they are considered to be a classic look that never quite goes out of style. However, there are certain trends that come and go and some people may think that Roman blinds are dated.
Ultimately, it comes down to personal preference and the look that someone is trying to create with their interior design. For those who prefer a more modern aesthetic, there are other window covering options such as roller blinds, blackout blinds, and even motorized shades, which can give a more contemporary look.
However, those who prefer a more classic and timeless feel may still opt for Roman blinds, as their style and texture gives a more timeless feel. Ultimately, whether Roman blinds are dated or not is a matter of personal preference.
Can I shorten roman shades?
Yes, it is possible to shorten Roman shades. The best way to shorten a Roman shade is to remove the existing bottom hem and trim the fabric to the desired length. For a cleaner hem, better fabric stability, and a longer-lasting treatment, you can re-hem the shade.
To do this, you will need to fold the bottom up to the desired length and iron in place, then create a new hem by creating a small fold along the edge of the fabric and ironing it in place. Finally, use a needle and thread to stitch the hem in place.
What is the difference between flat fold and soft fold roman shades?
Flat fold and soft fold roman shades are two different styles of window treatments. Flat fold roman shades are characterized by their sharp, crisp pleats and are created using a stiff fabric. This type of roman shade is ideally suited for modern and contemporary decors, but can also be made from fabrics that lend a traditional feel to the space.
Soft fold roman shades feature a more relaxed style and feature gentle, curved pleats. This type of shade is often created using a more lightweight fabric and can be a great choice for traditional and formal decors.
Both types of shades allow for a great deal of customization, making them a popular choice for many homeowners.