Putting string on a Husqvarna weed eater is relatively straightforward, though there are a few steps involved. First, turn off your trimmer and disconnect the spark plug for safety. Once you have done this, use a flathead screwdriver to remove the bump knob located at the bottom of the trimmer head.
This will allow you to remove the entire spool and cap. To add new string, hold the spool and twist the line counterclockwise as you pull out the required length of string. Cut the string using scissors, and then thread the line through the small hole in the end of the spool.
Once the line is through the spool, pull it back, twisting the line in a clockwise direction. Finally, replace the spool and cap, then replace the bump knob and spark plug. At this point, your Husqvarna weed eater should be ready for use.
What size trimmer line does a Husqvarna 128ld use?
The Husqvarna 128LD trimmer uses Husqvarna genuine trimmer line. Their trimmer line comes in a variety of sizes to suit your needs and the type of lawn or garden you are cutting. The sizes available range from 1.
3mm in diameter up to 4.0mm. The Husqvarna 128LD typically requires a 1.6mm diameter trimmer line which is suitable for most garden and lawn trimming needs. The very strongest and thickest line that should be used with the Husqvarna 128LD is 2.
5mm in diameter. You should avoid using any trimmer line thicker than this as it will put too much pressure on the motor and can cause damage. When replacing the trimmer line on the Husqvarna 128LD, it is always best to select a trimmer line that has been specifically designed for the model.
How do you fill a Husqvarna trimmer line?
Filling a Husqvarna trimmer line starts by ensuring the trimmer is turned off and unplugged before proceeding. Next, one should cut a piece of trimmer line that’s approximately 5-8 inches in length, then thread the line into the eyelet at the bottom of the trimmer head.
For curved eyelets, the line should be wrapped around the eyelet three or four times with the end exiting on the outside. After that, the trimmer head should be tightened firmly with an appropriate-sized wrench.
Lastly, the cutting head should be tested by running the trimmer in an open area to make certain the line has been installed correctly.
How do you remove the head on a Husqvarna 128ld?
Removing the head on a Husqvarna 128ld is a straightforward process that should take no more than 10 minutes to complete. Start by making sure the trimmer is switched off and unplugged, then use a Phillips head screwdriver to remove the screws from the engine cover.
Carefully pry off the engine cover to reveal the trimmer’s head assembly. Locate the two bolts that secure the head and use a socket wrench to remove them. Once the bolts are removed, the head should separate from the trimmer with a gentle tug.
If it does not come off easily, try gently rocking it back and forth from side to side. Once the head has been removed, replace it with a new head assembly, securing the new head in place with the two bolts and reattaching the engine cover.
How do you reload a trimmer spool?
To reload a trimmer spool, first you will need to cut off any old lines that are still on the spool. Once that is done, you will need to undo the cap on the spool and set aside. Then take your new line and thread it from the bottom of the spool, passing it through the line exit hole and tie off the end.
There should be a small notch at the exit hole; you can use this to help secure the thread. Once the new thread is secure and tied off, you can pull it tight towards the centre of the spool allowing for about an inch or two of thread overlapping the line exit hole.
For the last step, you will need to attach the cap back onto the spool, ensuring that all of the thread from the line is wound around properly, and your trimmer is ready to go.
How many cc is a Husqvarna 122C?
The Husqvarna 122C model is a lightweight grass trimmer powered by a 28cc two-stroke engine. This engine packs a punch for a trimmer of its size, but does require mix fuel for optimal performance. You will need a 50:1 mix of gasoline and two-cycle oil for correct operation.
The engine is designed with a centrifugal air cleaning system that helps keep it running longer, and helps to reduce emissions. The 122C is easy to start with a Smart Start system, and an easy to use auto return stop switch.
With an adjustable shaft, the Husqvarna 122C is suitable for all users, short or tall.
Are string trimmer heads interchangeable?
The answer to this question is that it depends on the type of string trimmer you have. Generally, most string trimmers will use interchangeable heads and will come with several types of heads to suit different tasks.
Heads can vary in size, shape, and material. However, some string trimmer models may not be compatible with some heads, so it’s important to check with the manufacturer if you’re unsure. In addition, if you’re using aftermarket replacement parts, ensure they are compatible with your specific model of string trimmer.
Finally, some string trimmers use a proprietary head system that is only compatible with their own replacement heads.
Are all trimmer heads the same?
No, not all trimmer heads are the same. Different trimmer heads are suited for different types of landscaping jobs, due to the variety of shapes and sizes available. Trimmer heads can come in a variety of styles, from bump-feed heads that require manually pushing the spool against the cutting head to advance the cutting string, to the more modern auto-feed style that advances the string with the touch of a button.
Some trimmers use blades instead of strings, while others use special attachments to do more than just trim grass. All of these different styles of trimmer heads make it easier to do complicated landscaping jobs, as well as increase efficiency.
How do you roll weed eater line?
Rolling weed eater line is a simple process that requires a few basic tools. First, place the spool of line on a flat surface and remove any packaging around it. Then, press one end of the line into the hole of the weed eater’s spool.
After that, hold a piece of foam and wrap the line around it to keep it in a tight coil. Next, wrap the line all the way around the spool leaving a few inches of line on the outside. Finally, cut the line at the outer edge and feed the excess line into the slot, then press the line against the side of the hole and press it down to secure it.
Following these steps will ensure your weed eater line is securely in place and you can start using it.
Why does my trimmer line not feed?
Your trimmer line might not be feeding for a few different reasons. The most common is that the line has become too short, or it is not wound tightly enough around the spool. If the line is too short, it can cause the trimmer head to become jammed or unable to spin freely.
A line that is not wound tightly enough may become loose and slip out of the head when it is engaged. Additionally, the head may be damaged or clogged, which will prevent the line from feeding through.
To troubleshoot this problem, check the trimmer head for any debris or damage and ensure the line is wound tightly enough around the spool. If it is, then you may need to replace the line with a longer piece.
What is a fixed line trimmer head?
A fixed line trimmer head is an attachment that is used in conjunction with a grass trimmer to cut grass and weeds. It uses a plastic line that is spun at high speeds to cut vegetation. This line is generally encased in a tube connected to the head, with the cutting edge of the line visible outside the tube.
The line typically has small, sharp blades, which work together to create a slicing action as the head is moved across the grass. Fixed line trimmer heads come in various different sizes, as well as different diameter lines, to enable the user to select an option that is most suitable for their trimming needs.
They are quick and easy to change and can help to reduce time spent on grass cutting tasks.
How do you change the spool on a Craftsman Weedwacker?
Changing the spool on a Craftsman Weedwacker is a relatively straightforward process. First, unplug the unit and lay it on a flat surface. Loosen the guard around the spool with an adjustable wrench and remove it.
Ensure there is no remaining line attached to the spool before removing it.
Next, take the replacement spool and insert it into the unit, ensure it is securely in place. Wrap the new line onto the spool and turn the line around the side spool tab to secure it. After ensuring the line is not twisted, pull the starter rope until the line is properly tensioned and cut off any extra line.
Replace the guard and use the adjustable wrench to make sure it is securely tightened into place. Turn on the Weedwacker and check to ensure the line is able to rotate properly. Finally, trim any grass and weeds as needed.