Recalibrating a Pedal Commander is a relatively simple process that can be completed in just a few steps.
Firstly, disconnect the Pedal Commander from the vehicle’s OBD-II port and turn the Pedal Commander off. Once the Pedal Commander is off, press and hold the Mode button while also pressing and holding the On/Off button.
The blue LED light should now flash, indicating that the Pedal Commander is in factory reset mode. Keep the buttons pressed for 10 seconds, after which the light should go off.
Next, reconnect the Pedal Commander to the vehicle’s OBD-II port and press the On/Off button once. This will initiate the calibration process and the unit will automatically detect the vehicle’s throttle body range and settings.
Once the calibrations has been completed, the Pedal Commander will show a green light for 10 seconds, indicating that the recalibration was successful. At this point, the unit is ready for use.
Can Pedal Commander damage your transmission?
No, Pedal Commander will not damage your transmission. It is an aftermarket throttle response controller that remaps your existing factory settings, making them more sensitive and/or aggressive. This can give your vehicle better response and improved acceleration.
Because Pedal Commander only adjusts the throttle response and not the actual gear shifting, it has no effect on the transmission and is not likely to cause any damage to the vehicle’s transmission. It is designed to be a safe product to use and has been rigorously tested to make sure that there are no adverse effects.
How much horsepower does the Pedal Commander add?
The Pedal Commander is designed to optimize your vehicle’s performance by delivering improved throttle response and more horsepower. Exactly how much horsepower it adds depends on your specific vehicle, but independent dyno testing has shown that there can be an increase of up to 20% in available horsepower and torque.
This increase in power is felt almost immediately after installation and calibration of the Pedal Commander. Additionally, the Pedal Commander includes 4 preset modes that allow you to choose between Eco, City, Sport, and Sport+ driving modes, allowing you to optimize your driving experience and maximize performance.
For vehicles equipped with a turbocharger, the Sport+ mode has the potential to add an additional 5 horsepower over the recommended Eco, City and Sport settings.
Where is the code behind Pedal Commander?
The code behind Pedal Commander is a highly advanced and incredibly intricate electronic system. It uses advanced algorithms to maximize the throttle response of your engine, translating your right foot commands into improved acceleration.
The primary component of the Pedal Commander system is the air valve adapter, which is what connects your vehicle to the system. This component reads the amount of pressure from your accelerator and sends that information to a central processor.
That processor then uses algorithms to inform the air valve adapter on the amount of air to adjust for improved performance.
Do you have to turn Pedal Commander on every time?
No, you do not need to turn Pedal Commander on every time. Once you have turned it on, your current settings will stay until you turn Pedal Commander off. Pedal Commander utilizes a built-in memory feature to remember your settings even after the ignition is switched off.
You will, however, need to press the power button each time you start the vehicle in order to activate Pedal Commander.
How do I get rid of throttle lag?
Throttle lag is a common issue that many drivers experience when driving vehicles with automatic transmissions. The issue occurs when your car takes an extended period of time to react to you pressing the accelerator.
Though frustrating, there are actions you can take to reduce the effect of this lag.
The first thing to do is to check your engine fluids and make sure they are clean and at the proper levels. Dirty and low fluids can cause a variety of issues with your vehicle, including throttle lag.
Additionally, you may want to discuss a transmission flush with your mechanic, as this can help clear away any accumulated dirt and gunk inside your transmission.
You can also check the quality of your air filter and spark plugs. Old and worn air filters may restrict air flow and reduce the performance of your engine. Similarly, worn spark plugs can cause misfires which will further reduce engine output.
Replacing or cleaning both of these components should help improve throttle response.
Finally, ask a professional to check the condition of your throttle body and ensure that all the sensors and connections are working properly. A faulty throttle body or bad sensors can cause a lag when you press the accelerator.
By taking these steps, you should be able to significantly reduce the throttle lag in your vehicle. Of course, if the issue persists, it may be worthwhile to have your car looked at by a professional.
Can dealership detect Pedal Commander?
No, Can dealerships cannot detect a Pedal Commander. A Pedal Commander is an aftermarket device that provides improved engine responsiveness and driving performance. It modifies the signal and adjust the parameters to provide better acceleration, improved throttle response and more refined vehicle control.
It is designed to be compatible with all types of vehicles, and it is undetectable by official mechanics or technicians, as it does not require any wiring or modifications to the car’s electronics. Therefore, it is virtually impossible for technicians at a dealership to detect a Pedal Commander.
Furthermore, even if the technicians were to somehow be aware of the device, they would not be able to tell whether it was functional or not, as their diagnostic tools are only able to detect electronic issues with the car.
How do I connect my Pedal Commander to Bluetooth?
To connect your Pedal Commander to Bluetooth, you will need to use the provided Pedal Commander app with your smartphone or tablet. First, you will need to make sure that your Pedal Commander is properly connected to your vehicle’s OBD2 port.
Once connected, launch the Pedal Commander app and select the Bluetooth option from the main menu. Make sure that your device’s Bluetooth is enabled, then turn on the power switch located at the back of the Pedal Commander.
This will enable the Bluetooth connection. Lastly, look for available Pedal Commander devices in the Bluetooth settings of your device, select it and you should be connected.
Does Pedal Commander remove speed limiter?
No, Pedal Commander does not remove the speed limiter. The Pedal Commander is designed to adjust the signal sent from your accelerator pedal to the Electronic Control Unit (ECU). The ECU is programmed by the manufacturer to control and limit the maximum speed of your vehicle based on the type of engine and setup.
The Pedal Commander can modify throttle response and sensitivity, but cannot override the speed limiter because the ECU is designed to limit speed and prevent over revving. To remove the speed limiter, you would need to reprogram the ECU and/or add aftermarket parts.
Does a pedal box add HP?
A pedal box can certainly add some horsepower to your car, however the exact amount will depend on your car’s make, model, engine size, and the type of tuning parts you’ve added. Generally speaking, pedal boxes allow for a finer control of the throttle when you press down on the pedal, allowing your engine to rev at optimal levels and transfer more power to the wheels.
A pedal box may also reduce the amount of travel on your pedal and increase the sensitivity as to when the pedal is engaged. Essentially, a pedal box allows you to squeeze more power out of your engine, allowing you to accelerate faster and possibly even hit higher top speeds.
If you already have a range of tuning parts and you want to increase performance or improve the responsiveness of your pedal, a pedal box can definitely help.
What all does a pedal commander do?
A Pedal Commander is an electronic device that connects to your vehicle’s throttle body, allowing you to customize how your vehicle responds when you hit the gas pedal. It gives you total control over your vehicle’s throttle response, allowing you to make it more responsive or even give it a “sportier” feel.
The Pedal Commander has four different user-programmable settings, including Eco, City, Sport, and Sport+, which offer different levels of pedal responsiveness. It also allows you to change the responsiveness of the accelerator pedal without having to install any permanent modifications.
Additionally, Pedal Commander’s “Adaptive Mode” allows your accelerator pedal to automatically adjust its responsiveness based on driving style and conditions. This helps conserve fuel, making your vehicle more efficient.
All in all, the Pedal Commander can help you get the most out of your vehicle, whether it’s a sports car or a daily commuter.
Does pedal commander work with a tune?
Yes, Pedal Commander can work with a tune on your vehicle. A tuned vehicle can require a different amount of throttle response than a stock vehicle, so the Pedal Commander can be adjusted to compensate for the tune.
Pedal Commander works by providing four adjustable modes that can be fine-tuned according to your preference. There is an Eco mode, City mode, Sport mode, and Sport+ mode. Each mode has their own general adjustments that can be further customized by sliding the dials.
You can choose between quick or smooth throttle response and adjust the power band for more or less torque. Ultimately, you can customize the performance of your vehicle with a tune and the Pedal Commander to find the perfect balance for your driving style and preferences.
Does PedalBox increase fuel consumption?
No, PedalBox does not increase fuel consumption. PedalBox is an engine optimization technology that is designed to improve engine performance and reduce fuel consumption. It does this by altering the throttle response of an engine, reducing the acceleration time between gear shifts, and optimizing engine mapping.
This helps to reduce engine wear and tear and ultimately results in lower fuel consumption. PedalBox also reduces throttle jerking, which can lead to excessive fuel use. Additionally, PedalBox has an ECO mode feature that helps to further optimize fuel efficiency, helping to save more fuel and money.
Is the pedal commander universal?
No, the Pedal Commander is not a universal device. It is compatible with a wide variety of vehicles, but not all. You will need to confirm that your vehicle’s make, model, and engine type is compatible with the Pedal Commander before purchasing.
This can be done by visiting their website and looking up your specific car. Compatibility is listed by vehicle type and engine type so you can easily verify that the Pedal Commander will work in your car.
Depending on the type of engine your car has, you may need the Bluetooth or Bluetooth + Wireless options for it to be compatible with the Pedal Commander. If your car is compatible with the Pedal Commander, it will help you improve throttle response, decrease turbo lag, and get quicker acceleration so you can get the most out of your car.