Before you start a chainsaw that has been sitting, you will want to make sure that it is in good working condition and that all necessary parts and components are present and in working order. With that being done, the next step is to make sure that the area you are working in is clear.
This means you should check for any loose objects, rocks, or branches that could potentially be a hazard. It’s also important to wear heavy-duty clothing and protective eyewear while handling a chainsaw.
When you are ready to begin, you should start by checking and filling the chain lubrication tank. This should be done with a high-quality commercial-grade chain lubricant as recommended by the saw’s manufacturer.
Once the tank is full, you can begin the process of starting the chainsaw. In general, this will involve connecting it to the gas tank and priming the engine with a starter bulb. You should always read the chainsaw manual carefully to ensure that you understand how to properly start the tool.
Before you pull the starter cord, you need to ensure that the chain brake is engaged and that the switch is set to the ‘On’ position. When you pull the starter cord, make sure that you hold the chainsaw level and even with both hands.
Doing this will reduce the chance of kickback, a dangerous phenomenon where the saw can quickly snap back and cause severe damage to the user. If the chainsaw starts up correctly, you can now un-engage the chain brake and get ready to use the saw.
What do you do when your Stihl chainsaw won’t start?
When your Stihl chainsaw won’t start, there are several things you can do to try to get it running again.
First and foremost, be sure you are following the manufacturer’s instructions for starting the chainsaw. If you skip any steps in the process, the chainsaw will not start.
Next, check the fuel in the chainsaw—there should be enough fuel, but it should also be at least 30 days old and not have any water or debris in it.
If you are certain the fuel is in good condition, pull away the fuel tank cap and look for any clogs or debris in the fuel filter. Clean out the fuel filter, if necessary.
If the fuel and fuel filter are in good condition, you may need to check the spark plugs. Remove the plugs and take a look. If they appear to be in good condition, try gap them first. If that does not help, it is time to replace the plugs.
Then move on to the air filter. Open the air filter cover and take a look. If it is dirty, replace it with a new filter.
If all of the above steps still do not work to start the chainsaw, you may need to check the compression. Check the compression between the spark plug hole and the cylinder head. If the compression is low, the piston rings may need to be replaced.
If all else fails, you may need to take it to a professional for further investigation.
What causes chainsaw to stop working?
Chainsaws are hard-working tools, but occasionally they can stop working for any number of reasons. Most commonly, chainsaws stop working due to a lack of oil, especially if the saw is used for continuous cutting.
This happens when the saw isn’t oiled frequently enough, and friction from the chain can cause it to stop working. Additionally, lack of fuel or incorrect fuel/oil mix can cause a chainsaw to stop running.
It is also important to check the fuel lines and filter to ensure that there is no clogging or blockage.
Other factors can cause a chainsaw to stop working, such as a poor spark plug or an old air filter. The spark plug is responsible for igniting the fuel and air mixture, and if it is faulty or worn out, it can cause the chainsaw to not start.
The same applies to the air filter; if it is clogged or not in good condition, the saw may fail to start. Lastly, a broken or loose chain can cause a chainsaw to stop working, as it will not receive enough tension to cut the material.
It is important to routinely maintain and inspect a chainsaw to ensure it is in peak working condition. Taking care of the oil levels, fuel and air mixture, air filter, and spark plug can help to prevent a chainsaw from unexpectedly stopping.
How do you unclog a chainsaw carburetor?
Unclogging a chainsaw carburetor usually involves cleaning the carburetor and removing any debris or other materials that could be clogging it up. The first step is to remove any air filter covers and air filters, and inspect the area to make sure there isn’t any debris or buildup inside.
If there is, use a soft brush to gently remove the debris. After that, disconnect the spark plug wire so that the chainsaw can’t accidentally be turned on while it’s being serviced.
Next, locate the carburetor and use a wrench to loosen and remove the screws that are attached to the carburetor. Once the screws have been removed, carefully lift up the carburetor and remove it from the chainsaw.
Pay special attention to the housing of the carburetor and try to remove as much dirt, dust, and debris as possible. A vacuum cleaner can help remove this kind of buildup.
Next, use carburetor cleaner to clear the passageways of the carburetor of any deposits or dirt. This can be done with a carburetor cleaning solution and a carburetor cleaning brush. For best results, repeat this process a few times until the passageways are devoid of any debris.
Finally, reconnect the carburetor onto the chainsaw and reattach the screws firmly. Test the chainsaw to make sure it’s working properly. Also, check the air filter and the air filter cover to make sure they’re in place and sealed correctly, as the chainsaw will run more efficiently when that’s taken care of.
Hopefully, this has cleared your chainsaw carburetor and it is back to working properly.
How do you clean a carburetor on a chainsaw without removing it?
Cleaning a carburetor on a chainsaw without removing it is a fairly simple process but it is important to note that it should be done carefully and accurately in order to ensure the best performance.
To begin, you will need to remove the air filter of your chainsaw, typically by removing a couple of screws or a pull-tab. This will give you access to the carburetor. Next you will need to remove the spark plug wire and the spark plug itself.
Then you will need to spray a small amount of carburetor cleaner into the carburetor while turning the chainsaw over. This will help to loosen and remove any debris and gunk that may have built up inside the carburetor over time.
Once you are finished with this step, you will need to dry the carburetor with a clean rag to make sure all of the sprayed cleaner is removed. After finishing this step you should be able to start the chainsaw.
However, if the cleaning process was not done correctly it is possible the chainsaw may have some running issues. In this case, it may be best to remove the carburetor from the chainsaw and clean it more thoroughly.
How do you fix a chainsaw that doesn’t work?
Fixing a chainsaw that doesn’t work requires assessing the issue and taking the necessary steps to get it working. First, check that the chainsaw is receiving fuel and that the fuel to oil mix is correct.
Often, adjusting or replacing the air filter will help. If the issue is related to the spark plug, you may need to replace it or make sure that the spark plug area is clean. If the bar and chain are stuck, try loosening them and then apply lubrication.
Next, ensure that the chainsaw has enough bar and chain oil. Finally, examine any damaged parts and replace them if needed. If the problem persists, it is best to contact a professional.
Why does my chainsaw stop running after a few minutes?
The most common issue is that the spark plug needs to be replaced. This can happen if your chainsaw isn’t regularly serviced or has gone unused for a while. Sometimes the spark plug wires can fail too, interfering with the connection of the spark plug to the ignition system.
Another possible cause is that the fuel filter may be dirty or clogged. This prevents fuel from flowing freely to the engine, resulting in the chainsaw stalling or cutting out.
It could also be due to a faulty ignition switch or wiring, or problems with the fuel/air mixture. If the compression check reveals low compression then it could be due to worn piston rings or faulty valves.
If the chainsaw has been damaged in an accident or suffered a hard landing, it may also affect the ability for it to stay running for more than a few minutes.
In all cases, it’s best to take your chainsaw to a professional for for servicing and repair.
Why does my chainsaw shut off when I give it gas?
The most common cause is an issue with the fuel/air mixture. The carburetor on a chainsaw is responsible for ensuring the right amount of fuel and air enters the engine. If the fuel and air mix is not correct, it can cause the engine to shut off.
Other possible causes could include a clogged air filter, a bad spark plug, or a faulty ignition coil. Additionally, it could be due to a dirty fuel tank or fuel line. It is important to use fresh fuel that does not contain any dirt or debris as this can clog a fuel line.
Another possible cause for an engine shutting off when giving it gas is a worn-out fuel filter. A fuel filter prevents any dirt and debris from getting into the carburetor and engine. Over time, a fuel filter can become clogged, causing the engine to shut off when giving it gas.
Your chainsaw should also be properly lubricated and maintained to ensure the engine does not overheat, which can also cause it to shut off. It is important to check the oil, spark plug, and air filter on a regular basis.
If all of these items are in good condition and the fuel/air mixture is correct, it is possible your chainsaw has a faulty part and will need to be serviced.
Should you run a chainsaw at full throttle?
No, you should not run a chainsaw at full throttle. The reason for this is because running a chainsaw at full throttle can damage the chainsaw engine, reduce the life of the chainsaw, and compromise the safety of the operator.
Running a chainsaw at full throttle results in higher engine temperatures and increased wear on the piston and cylinder. This will cause the engine to run inefficiently, losing power and torque. In addition, running a chainsaw at full throttle could cause a kickback, and kickbacks can be extremely dangerous.
If a kickback occurs, the operator can be thrown off balance and lose control of the saw, resulting in serious injury or death.
It is important to always keep the throttle at a low speed until you are ready to use the saw. This will help reduce stress on the engine and help maintain optimal power and efficiency. When actually cutting, it is best to increase the throttle gradually, allowing the chainsaw to reach the appropriate speed before actually cutting.
This will help reduce kickbacks and improve safety.
How do you troubleshoot an electric chainsaw?
To troubleshoot an electric chainsaw, first check the basics. Make sure the power switch is on and that the safety switch is engaged. Ensure that the power cord is securely connected and the plug is working properly.
Then, adjust the chain tension if necessary; the chain should be able to move freely about 1/4 inch up and down. Make sure the bar and chain oil are filled; the bar oil should be at least 1/4 inch above the bottom of the tank.
If the electric chainsaw isn’t running, try using compressed air to clean the fan and motor vents. If there is no power, check to make sure the electric circuit breaker isn’t triggered. If the engine is running but the chain isn’t moving, it could indicate a clogged chain or a worn motor drive/bar.
Also inspect the drive/bar housing to make sure it is securely in line with the guide bar.
Finally, regularly service the chainsaw by inspecting the spark plug and wire, checking the compression ratio, and cleaning or replacing the air filters. Be sure to follow the manufacturer’s instructions for servicing and use the recommended parts.
Why did my chainsaw suddenly stop?
Your chainsaw could have stopped suddenly for a variety of reasons. The most common cause is if the chain or chain bar is clogged with dirt or debris, or if the chain is dull. If the chain has gotten too hot, the motor will overheat and shut off.
An obstruction caught in the chain guard or the chain itself could also be preventing the chain from spinning. Another likely cause could be a lack of lubrication. A chainsaw needs to be kept lubricated to keep it running smoothly and for the chain to cut properly.
It’s also possible that the spark plug has become fouled or that the fuel mixture is off, causing the engine to quit running. Lastly, it could be a problem with the ignition system or the carburetor, in which case it would need to be serviced or replaced.
Do electric chainsaws have fuses?
Yes, electric chainsaws typically have fuses as a safety feature. The fuse is usually found inside the tool’s handle and is designed to protect the internal electric components from potentially hazardous current levels.
If the current exceeds the acceptable limits, the fuse will blow so that it does not overload the tool’s components. If a fuse is blown, it will need to be replaced before the tool will operate again.
Most electric chainsaws come with a spare fuse that can be used to replace a blown fuse. It is important to make sure that you buy the correct size and type starting fuse as too large or too small of a fuse could lead to further damage to the tool.
Why is my chainsaw not oiling the chain?
If your chainsaw isn’t oiling the chain, it could be caused by a few different issues. First, make sure that the oil tank is full and that the oil is not blocked, as this can prevent oil from reaching the chain.
If the oil tank is full and there are no blockages, then the issue could be caused by a defective oiler or an air leak. A defective oiler could have a faulty switch or worn out seal, while an air leak could be caused by debris or a defective gasket.
If all else fails, it is recommended to consult with a Chainsaw specialist as there could be a more serious underlying issue with your Chainsaw that needs to be addressed.
How do you stop a Dewalt chainsaw from leaking oil?
To stop a Dewalt chainsaw from leaking oil, the first step should always be to check the oil level and add oil if necessary. Make sure to use the correct type of oil for the chainsaw, as specified by the manufacturer.
If the oil level is sufficiently high, the next step is to check the oil seals which are often located below the oil reservoir. These may have worn out and need replacing. Additionally, check the fuel tank cap to make sure it is properly sealed.
If that doesn’t help, the next step is to check the fuel and air filter. Clogged or worn filters will cause the chainsaw to leak oil. If the fuel and air filter are both clean and correctly installed, the oil seals may need to be replaced.
Lastly, the oil tank’s vent hose should be inspected, as a clogged vent hose can cause the chainsaw to leak oil. With proper maintenance and periodic inspections, a Dewalt chainsaw should not leak oil.
How do I contact Dewalt tools?
If you are looking to contact Dewalt Tools, there are several different methods you can use depending on the type of inquiry that you have. For general product inquiries or customer service assistance, you can contact their customer service department by phone, Monday to Friday, 7:30am to 8:00pm (EST) at 1-800-433-9258 or you can e-mail them at ServiceC@sbdinc.
com or fill out the Contact Us form on their website.
If you are looking to find the nearest retailer of Dewalt Tools products, you can utilize the store locator on their website, which will help you find what store locations are nearest you.
If you are looking to purchase items directly from them, they have an e-commerce website that allows you to browse their products and add them to your shopping cart to make purchases.
For specific inquires or requests, you can also reach out to their customer care team via their social media accounts (Facebook, Twitter & YouTube). You can also speak with expert technicians by calling 1-800-4-DEWALT for technical advice.
Finally, you can use their contact us form to inquire about sales, promotions, warranties, account related inquires and more.
How do you start a Makita 16 inch chainsaw?
Starting a Makita 16 inch chainsaw is fairly straightforward. First, make sure the chainsaw is in the off position and the chain brake is engaged. Next, fill the fuel tank with a mix of two-cycle engine oil and gasoline, according to the ratio specified in the owner’s manual.
After fueling, pull the choke knob to the full closed position. Then, press the primer bulb five times to fill the carburetor with fuel. Finally, turn the ignition switch to the on position and press the throttle trigger twice, or until you hear the motor running.
Now the Makita 16 inch chainsaw is ready for use.
What fuel does a Makita chainsaw use?
Makita chainsaws usually run on a two-stroke engine, which require a special fuel mixture of unleaded gasoline and two-stroke oil. The oil serves as both a lubricant and a fuel source for the engine.
You need to ensure that you use the proper fuel mixture for your Makita chainsaw in order to keep it running efficiently. Most Makita chainsaws require a 2-stroke oil and gasoline mix, with a ratio of 50:1 (two-stroke oil to gasoline).
This means for every one gallon of gasoline, you should mix in two and a half fluid ounces of two-stroke oil. It’s important to not use a four-stroke oil, as this can damage the machine.
How do I turn on Makita?
To turn on Makita power tools, locate the On/Off switch on the tool. It will typically be a sliding switch at the back of the machine. If the switch is already in the On position, the tool will be ready for use.
If the switch is in the Off position, slide it towards the On position and the tool will be ready for use. If a tool has a locking switch, you may need to press or rotate it before sliding the switch to On.
Does Makita chainsaw need oil?
Yes, Makita chainsaws need oil to lubricate the internal moving parts and keep the saw in peak operating condition. The oil helps to reduce friction and heat build-up, and protect the saw’s engine components.
Make sure to use a chainsaw oil specifically designed for chainsaws and never use motor oil because it can cause damage to the saw engine. The amount of oil needed will vary depending on the model and types of cutting jobs being done.
In general, you should use enough oil to cover the lower part of the chain. Be sure to read your Makita chainsaw’s user manual for specific instructions and safety precautions when using oil.