To tighten a Poulan chainsaw chain, you will first need to inspect the chain’s tension. You can do this either by simply pushing the chain away from the engine and noting how far the chain moves or by using a chainsaw chain gauge.
If the chain’s tension is too loose, you will need to add some tension in order to tighten it up. To do this, you will need to locate the tension screw located on the side of the chainsaw. This is usually done by detaching the chainsaw’s side cover and looking for the small screw on the lower side of the chainsaw.
Once located, you will then need to adjust the tension screw by turning it clockwise with an adjustable wrench or pliers. You will then need to check the tension after each turn by pushing the chainsaw away from the engine and checking the movement.
Once you reach the desired tension, you will then need to secure the tension screw with a nut. Finally, test the chainsaw’s tension again by running it through a few test cuts.
Where is the tension screw on a chainsaw?
The tension screw on a chainsaw is typically located behind the bar and chain on the side of the chainsaw. To properly tension your chainsaw’s chain, you need to locate the tensioning screw behind the chainsaw’s bar and adjust accordingly.
The tension screw is usually a slotted screw head located at the bottom of the chainsaw’s body near the rear handle of the chainsaw. The tension screw is used to snug the chain down onto the guide bar.
When tensioning the chain, be sure to only tighten the screw a quarter turn at a time, as over-tensioning could cause serious damage to the internal parts of the chainsaw. Once the proper tension is achieved, you can shut off the engine and use the chainsaw to cut whatever material you need.
Why does my Poulan chainsaw dies when I give it gas?
Your Poulan chainsaw could be dying when you give it gas for a few reasons. The most common cause is a problem with spark plug functioning. If the spark plug is malfunctioning, it may not be generating a spark to ignite the fuel-air mixture, leading to the engine dying when you apply gas.
To check whether the spark plug is the issue, first remove the spark plug and check if it is wet or dirty. If it’s either of those, clean and dry it, then re-install it. If the spark plug looks clean, use a spark plug tester to make sure it is working properly.
A second common cause for the engine dying when you give it gas is a clogged carburetor. If the carburetor is clogged, it is not mixing the proper amount of fuel and air, leading to the engine stalling when you apply gas.
Cleaning or replacing the carburetor may be necessary to address this issue.
Finally, if your Poulan chainsaw has been sitting for an extended period of time, the fuel may have gone bad and left deposits on the carburetor. This may be causing the engine to die when you give it gas.
If this is the case, it may be necessary to clean the carburetor and replace the fuel with fresh, high quality gasoline.
If your Poulan chainsaw is dying when you give it gas, closely inspecting the spark plug, carburetor, and fuel quality should help you to diagnose the issue and take the appropriate steps to fix it.
What do the high and low screws do on a chainsaw?
The high and low screws on a chainsaw play an important role in regulating and maintaining the performance of the machine. The high screw adjusts the amount of air that enters the engine, while the low screw controls the amount of fuel and determines the speed of the engine.
By adjusting the screws, the engine can be equipped to function more efficiently and safely.
Increasing the high screw causes the engine to draw in more air and can result in a reduction of fuel being used and a higher operating speed. As a result, the handling of the chainsaw will also become harder and more jerky as the air-fuel mixture becomes less combustible.
In contrast, decreasing the high screw slows the engine down by reducing the air intake, which produces a more combustible air-fuel mix. The engine will become easier to handle as the power is reduced, but it won’t be able to reach its maximum speed.
The low screw, on the other hand, controls the amount of fuel that enters the engine. Turning the low screw clockwise will result in more fuel flowing into the engine and will create a louder running noise as the chainsaw delivers its maximum power.
However, this can also lead to excess smoke being produced and a decrease in fuel efficiency. It is important to adjust the low screw with caution, as having too much fuel passing through the engine can cause the chainsaw to overheat and malfunction.
Adjusting the screws on your chainsaw is important for producing efficient and safe performance. Doing so effectively requires careful monitoring and adjustments to ensure that the engine is running optimally and is not causing any potential damage to the machine.
How do you adjust the carburetor on a Poulan Pro?
Adjusting the carburetor on a Poulan Pro involves important steps that should be taken in order to ensure the proper functioning of the engine. It is important to be familiar with the specific model of the Poulan Pro’s engine to ensure the adjustments are made correctly.
Before adjusting the carburetor, it is important to ensure that the spark plug, vent, and filter are all clean.
The first step in adjusting the carburetor is to adjust the high and low speed screws. Start by turning the high speed screw counterclockwise until the engine is at its highest idle speed. If the engine is running at an abnormally high speed, turn the high speed screw clockwise until the engine reaches its optimal level.
Next, turn the low speed screw counterclockwise until the engine idle speed is at its lowest point. Seek professional assistance if the engine is fluctuating or surging during the adjustment.
Once the high and low speed screws have been adjusted, the next step is to adjust the idle mixture screw. This ensures that the correct amount of fuel is mixed with the air to achieve optimal running.
To adjust the idle mixture screw, turn it counterclockwise until the engine stops and smoke appears from the exhaust. Then, turn the screw clockwise until the engine emits a normal exhaust.
By taking all these steps, you will be able to adjust the carburetor of a Poulan Pro accurately and properly and ensure optimal performance of your engine.
What chain does a Poulan P3314 use?
The Poulan P3314 chainsaw uses a 14-inch bar and chain. It has a powerful 33cc two-cycle engine with a primer bulb, providing maximum efficiency and easy starts. This chainsaw has regular 3/8-inch pitch, low profile 0.
043-inch gauge and 62 drive link chain. It is a lightweight and durable construction that provides smooth, comfortable operation. The automatic gear-driven oiler gives precise oiling and the adjustable automatic chain tensioner takes the guesswork out of chain tensioning.
The chain brake and chain catcher help protect the operator from kickback. This chainsaw includes a carrying case, a replacement chain, and a chain adjuster tool.
What is chainsaw tool?
A chainsaw is a powered cutting tool used in logging, tree maintenance, and other applications involving cutting trees or wood. It is normally powered by gasoline, electric, or pneumatic engine. The chainsaw typically consists of a cutting bar, with a chain of sharp cutting edges connected to it and driven around the bar.
This allows the user to make precise, straight cuts into the material. Chainsaws are used in a variety of ways, such as tree pruning, tree felling, and bucking limbs. As the name implies, a chainsaw uses a chain of saw blades to do the cutting.
The blades drive the chain around a bar, which helps guide the chain and keep it in place as it cuts through wood. Chainsaws come in a variety of sizes and styles and are made from several different materials.
The most popular models are gasoline-powered, but electric and battery-powered chainsaws are also available.
What size is a Stihl chainsaw wrench?
The correct size of wrench to use for a Stihl chainsaw is a 13-millimeter, 8-point socket wrench. Double-check your chainsaw’s owner manual for the exact wrench size and shape to ensure the best fit for your tool.
It may be different for different models. Before purchasing a wrench, make sure the size is capable of taking off the nuts and nuts or bolts that secure the chainsaw chain or the throttle cable or other moving parts.
Additionally, it’s always a good idea to wear safety gloves when working on a chainsaw.
How do you use a Scrench?
A scrench is a multi-purpose tool for bicycles. It is generally comprised of two sections of hardened steel, one of which acts as a screwdriver, and the other as a wrench. To use a scrench, you first locate the screw or nut that you wish to loosen or tighten and choose the appropriate end for the job.
Once the correct end has been chosen, it is inserted into the bolt or nut in question and then turned clockwise or counter-clockwise depending on whether you are tightening or loosening the fastener.
It is important to use steady pressure and to avoid exerting too much force, as this could damage the fastener. Once you have achieved the desired level of tightness or looseness, you can then remove the scrench and move on to the next task.