The expected lifespan of an LED outdoor light will vary depending on the type of LEDs used and the specific conditions in which it is used. Generally, though, LEDs can last anywhere from 25,000 to 50,000 hours.
This means that if your outdoor light is used 12 hours per day, the expected lifespan should be anywhere from 8 to 16 years. It’s worth noting, however, that harsher environments may reduce the lifespan of your outdoor light.
Places with a lot of dust, extreme temperatures, and high levels of moisture, for instance, could not only reduce the lifespan of the light, but also its efficiency. Despite such circumstances, LEDs usually last longer than traditional outdoor lighting options — up to five times longer than halogen or incandescent exterior lighting.
Thus, over the long haul, LEDs are often worth their higher initial cost.
How long do LED lights actually last?
LED lights can last for an incredibly long time. Depending on factors like the type of LED, quality, and the environment in which they are used, LED lights can last between 25,000 and 50,000 hours. This means that, at the low end of the scale, LED lights can be expected to last for roughly 3 years, with the potential to last for up to 10 years and beyond.
This is far longer than traditional incandescent bulbs, which usually last for only 1,000 hours or fluorescent bulbs which last for about 8,000 hours. LEDs are also known for their durability, making them much less likely to break down or need replacing than the other types of bulbs.
How do I reset my good earth LED lights?
Resetting good earth LED lights is a straightforward process that requires the use of a breaker or switch for your unit. If you have a breaker on your unit, first turn off the breaker and then unplug the unit from the wall.
After that, reinstall the breaker and turn it back on, plug the unit back in, and switch the light switch on to reset the LED light.
If your light system doesn’t have a breaker and instead has a switch, the process is much the same. Simply turn off the switch, unplug the unit from the wall and plug it back in, and then turn the switch back on.
Once the switch is back on, the LED light will reset.
For more detailed instructions and specific troubleshooting, it is recommended that you consult your manufacturer’s instructions manual.
Why do outdoor LED lights fail?
Outdoor LED lights can fail for a variety of reasons. One of the most common is water damage, which can occur if fixtures are not installed properly or are exposed to excessive moisture. Other causes of LED failure include excessive heat from the sun, electromagnetic interference from nearby sources, and power surges.
In addition, poor quality or damaged LED chips or components can cause a premature failure of an LED light. Poor installation can also result in premature LED failure, as can inadequate power supply and not using the correct current or voltage.
Furthermore, inadequate heat dissipation from an LED driver can also cause an LED light to fail prematurely.
Why would an outdoor light stop working?
There can be a number of reasons why an outdoor light may stop working, such as electrical problems, mechanical issues, bad weather, advances in technology and more. Electrical problems may be the result of wiring issues, a faulty switch, insufficient power supply or blown bulbs.
Mechanical issues could include a broken fixture or loose parts. Bad weather such as strong winds, rain or snow can also cause outdoor lights to malfunction as the wires may become damp and eventually short circuit.
It is also possible that advances in technology can make the outdoor lights no longer work as the controls and components may be outdated and no longer compatible.
How do I choose under cabinet lighting?
When choosing under cabinet lighting, there are several factors to consider. First, determine the size of the lighting fixture required. Under cabinet lighting is available in various sizes such as strips and bars, so it is important to measure the area before making your purchase.
Secondly, decide whether you want an LED or fluorescent lighting option. LED lighting offers a long lifespan and superior energy efficiency, while fluorescent lighting is generally less expensive but consumes more energy and provides less light.
Thirdly, consider the design of the lighting. Under cabinet lighting is available in stylish and modern designs, so it is important to find one that complements the overall aesthetic of your kitchen.
Additionally, ensure the under cabinet lighting you choose offers sufficient lighting for your space. Lastly, it is recommended to buy from a reputable brand as this will ensure that you are getting a quality product that will last for many years.
What kind of lights do you put under kitchen cabinets?
Under kitchen cabinets, you’ll typically want to install either plug-in puck lights, LED tape lights, or LED light strips. All of these types of lights offer great energy efficiency, as well as convenience and illumination.
Puck lights typically have a low profile, so they can fit in many tight spaces, and they are available in both LED and halogen versions. LED tape lights come in a variety of colors and brightness levels, and they are adhered directly to the underside of a cabinet or other surface.
LED light strips are another great option as they provide plenty of light and can be easily cut to any length you need.
When choosing the best type of light for a particular cabinet, consider how much light you need and how much space you have to work with. Also think about the effect you want to achieve, as various colors can provide a warmer or cooler light depending on the atmosphere you are creating in the room.
Whatever you choose, you’ll be able to find lights with minimal wattage so you can save on energy costs.
How bright should under cabinet lights be?
Broadly speaking, the brightness of under cabinet lights should be determined based on the type of lighting being used and the purpose of the lighting. For example, if you are trying to create a low key atmosphere in your kitchen, you may opt for something with a lower lumen output.
On the other hand, if you are looking for lighting to be able to clearly see food preparation activities, you will likely want to choose something higher on the lumen scale.
For task lighting, a good rule of thumb is to use bulbs that are around 500 lumens or higher. If you are working with halogen lights, the range of brightness can span from 25-90 watts. If you are using LED undercabinet lights, it can be beneficial to choose a light fixture that provides dimming capabilities, so that it can be adjusted to the level of brightness you desire.
Ultimately, the brightness of under cabinet lights should be determined by the task and atmosphere of the room, as there is no single definitive answer.
What color light is for kitchen?
The type of color light used in a kitchen can vary depending on personal preference. Generally, natural light from windows is best for the kitchen during the day as it helps to create a bright and inviting atmosphere.
However, during the night, warm white light is usually the preferred lighting for the kitchen. Warm white lighting is usually between 2700K-3000K on the Kelvin Scale and is a comfortable light to work in for most tasks.
It has a relaxing, yellowish hue that can make tasks easier on the eyes, making it an ideal choice for the kitchen.
Is cool white or warm white better for kitchen?
This is a very subjective question and will depend on personal preference as well as the kitchen decor and lighting installation.
For many, cool white is the most commonly used light for general lighting in a kitchen. It has a bluish tint and often creates a bright, modern and energetic look. The bright white spill can reflect off of surfaces such as countertops and walls, creating a light and airy feel.
Cool white often creates a crisper and brighter look, showcasing the kitchen to its fullest potential.
Warm white is often seen in more traditional or cozy settings and has a yellowish hue. It’s more inviting and welcoming than a cool white, creating a cozy environment. While warm white won’t bring out the same level of detail as cool white can, it still provides plenty of lighting while creating a cozy atmosphere.
In the end, it really comes down to personal preference. Think about the overall aesthetic of the kitchen, and choose a light that best compliments it. Whether you are looking for a crisp, modern look or a warm, inviting atmosphere, the right choice can help to create the perfect kitchen lighting.
Do I want daylight or soft white?
When deciding between daylight and soft white light bulbs, it’s important to consider the lighting needs of the room and the type of activity that takes place there. Daylight bulbs provide a “cleaner” light, with a more natural tone, whereas soft white bulbs add a warmer, more inviting glow.
Daylight bulbs are generally bluer in tone and intended to replicate natural lighting. Their brightness level is measured in Kelvin (K). In general, bulbs that are 3000K and above are considered daylight, while those with a temperature of 2700K or below are soft white.
Daylight bulbs are best suited for spaces that require higher levels of visibility, such as kitchens and bathrooms.
Soft white bulbs on the other hand, come in temperatures ranging from 2700K to 3000K. They are generally warmer and better suited for living rooms and bedrooms, offering a cozy and inviting atmosphere.
If you are struggling to choose between the two, consider the atmosphere that you want to create in the room. If you’d like more visibility and clarity, then daylight is the right choice. However, if you’d like to create a more relaxed atmosphere, then soft white is the better option.
Is 3000K or 4000K better for a kitchen?
It depends on your preferences and the atmosphere you are aiming to create in your kitchen. 3000K is a softer white light that is great for creating a warm and cozy atmosphere, while 4000K emits a daylight-like cool white light that is better suited to kitchens where you are looking for a bright and clean look.
Ultimately, it comes down to personal preference and what type of atmosphere you are looking to create.
What light bulbs should be used in kitchen?
When selecting the light bulbs to use in the kitchen, you should consider several factors.
First, consider the amount of lighting you need for each task. For general lighting, LED or CFL bulbs are ideal because they produce a brighter light and are more energy efficient. Task lighting should be more focused, and requires brighter bulbs.
Incandescent bulbs and halogens bulbs are best for this type of lighting.
Next, consider the lighting fixtures you have in the kitchen. Make sure you select bulbs that are compatible with the fixtures. Consider the size of the base, and the wattage, voltage, and type of bulb.
For example, you can use a longer, lower-wattage CFL bulb in a fixture made for an incandescent bulb, but you may need to use an adapter.
Finally, consider the color temperature of the light bulb. This is indicated in Kelvin ratings and is measured on a scale from warm yellowish light to cooler white. Settings with warm yellowish light, such as 2700 to 3000 Kelvin, are ideal for kitchen, because they are most reminiscent of natural sunlight and can help create a cozy atmosphere.
When selecting light bulbs for the kitchen, it is important to consider the amount of light you need, the lighting fixtures you have, and the color temperature you are looking for. LED and CFL bulbs are good for general lighting, while incandescent and halogen bulbs are best for task lighting.
Warmer color temperature is also recommended for the kitchen.
How do you link Good Earth LED lights to Alexa?
In order to link a Good Earth LED lights to your Alexa device, you will need to install the Good Earth app on your compatible device and link the lights using the app. Once the lights are linked through the app, you can ask Alexa to control the lights using your voice.
To start, make sure the Good Earth LED products are connected properly and powered on. Then, update the app to the latest version. You can then open the app and follow the pairing instructions to connect Alexa to the lights.
Once successfully paired, you will need to configure your Alexa device with the app. Open the Alexa app, go to Settings, and select the Smart Home tab. Under Smart Home Skills, search for and connect the Good Earth LED skill.
Then, enter your Good Earth LED app credentials to complete the setup. Once completed, the Alexa app will display all Good Earth LED light groups. That’s it! You are now ready to control your Good Earth LED lights with your voice. Enjoy!.
How do you hook up LED lights?
Connecting LED lights is relatively simple and straightforward. Generally, you’ll need to connect the LEDs in series, meaning each LED will be wired in a chain from the power supply to the final LED in the chain.
To hook up LED lights, you’ll need the proper supplies: LEDs, a power supply, wiring, and connectors.
1. Choose an appropriate power supply to power your LED lights. Make sure the power supply can provide enough output to power your lights and meets its voltage requirements. A power supply will usually have an output rating such as 12 volts DC or 24 volts AC that you need to match to your LEDs.
2. Connect the positive and negative wires of the power supply to the proper wires of the LED lights. If you’re using multiple LEDs, connect the positive wire of the power supply to the positive wire on the first LED, then the negative wire of the first LED to the positive wire of the second LED, and so on.
3. Connect the positive wire of the last LED in the chain to the negative wire of the power supply. This will complete the circuit and allow the power to flow through the LEDs.
4. Secure the wire connections with connectors or other means as needed. Lastly, turn on the power to ensure the LEDs light up properly.
It’s important to take extra precautions when connecting LED lights, such as making sure each LED has the correct polarity, the positive and negative ends are connected correctly, and all the wiring is properly secured.
Additionally, the power supply you choose should be able to handle the total load of all connected LEDs. By following the instructions above, you can easily connect LED lights correctly.
How do you install LED cabinet lights?
Installing LED cabinet lights is a relatively easy and simple process, depending on the specific model of lights that you purchase. Generally speaking, the installation process includes the following steps:
1. First, make sure you turn off the breaker or switch that powers the cabinet lights.
2. Next, if the lighting you are replacing is fluorescent or halogen, you may need to remove the existing ballast and/or transformer.
3. Once that is done, clean the area thoroughly and make sure all the dust and dirt is removed from the inside of the cabinet.
4. Once the area is cleaned, measure and mark the area where the LED cabinet lights will be mounted.
5. Then, using the provided screws, mount the LED cabinet lights to the installed frame.
6. Following the manufacturer’s instructions, attach the wiring to the cabinet lights.
7. Then, connect the power cable to the power supply, either directly or via a junction box.
8. Finally, test the LED cabinet lights to make sure they are working and no connections are loose.
If you are unsure of any of the steps above, you should seek professional assistance to ensure the installation is safe and done appropriately.
How do you wire undercounter lights?
Wiring undercounter lights involves connecting the electrical supply to a fixture, connecting the fixture components, and wiring them into a junction box. The specific steps involved in this process depend on the type of lights being installed and the type of wiring used.
Before beginning the wiring process, turn off the power at the circuit breaker that will be supplying the electricity to the undercounter lights. It’s also important to check that line voltage circuits are properly insulated from ground wires.
Assuming the undercounter lights you are wiring are to be connected to a receptacle, follow the below steps for wiring:
1. Install the junction box where the wires will be connected. This can be attached to a stud or wall, or may be supported by metal boxes.
2. Install the lights into the junction box. Make sure you’re using the correct box for the type of lights being installed.
3. Run Romex or metal-sheathed cable from the junction box to the electrical receptacle.
4. Connect the exposed bare copper wire to the grounding screws in the junction box and receptacle.
5. Connect the black wire to the brass screws on the junction box and receptacle.
6. Connect the white wire to the silver screws on the receptacle and junction box.
7. Finally, secure the junction box and receptacle covers.
Properly wiring undercounter lights is essential for the lights to operate safely. If in doubt, you should always hire a professional electrician to complete the wiring.
Are LED strip lights good for under kitchen cabinets?
Yes, LED strip lights are a great option for under-cabinet lighting in a kitchen. LED strip lights provide a soft, even light that is excellent for task lighting and creating ambiance in a kitchen. LED lights are also very energy efficient, they last longer than traditional incandescent bulbs, and they come in a variety of shapes and colors.
Additionally, LED strip lights can be easily installed on the bottoms of kitchen cabinets, allowing for easy access to the wiring and controls. All of these factors make LED strip lights an excellent choice for lighting up the bottom of kitchen cabinets.