A fixed line head on a strimmer, also referred to as a trimmer head, is the component of the strimmer that houses and dispenses the nylon wire or nylon filament that is used to trim grass or other vegetation.
Unlike other types of strimmer heads that are designed to use plastic blades, the fixed line head uses only the nylon wire or filament to cut through the vegetation. This makes it a preferred choice for cutting thicker vegetation, as the nylon wire is more resilient and capable of far more rigorous cutting than the plastic blades used in other types of strimmer heads.
The fixed line head is designed with a hollow center to accept the spool of string, making it possible for the string to be easily replaced when the old one wears out. Additionally, some fixed line heads are adjustable, allowing for different lengths and widths of string to be used in the same head.
This makes the head ideal for larger areas of vegetation, where different lengths and conditions of grass require different string lengths.
How do you load a universal trimmer line?
Loading a universal trimmer line can be done in a few easy steps. First, using a Phillips screwdriver, loosen the screws of the trimmer head, then remove it from the engine. In the center of the trimmer head, you should see a spring and a spool with the trimmer line on it.
To take out the spool, remove the spring, and then the spool will come off freely.
Check if the ends of the trimmer line are broken or frayed and then gently remove the old one, being careful not to break the new line while doing so. If the spool is empty, you need to fill it with the new trimmer line, making sure the line’s end lays down on the line slot.
For a dual-line trimmer, you should fill the spool with both lines.
Once you have the trimmer line set up, you need to thread it properly. As this will depend on the trimmer, please refer to your manual for specific instructions. When all is done, reassemble the trimmer head, starting with the spring and re-tightening the screws carefully.
Test that the trimmer lines feeds properly and now your universal trimmer line is loaded and ready to use.
How do you string a head trimmer?
Stringing a head trimmer requires two key steps: prepping the trimmer head and winding the trimmer line. To prep the trimmer head, first remove the metal cap covering the spool. Set aside the metal cap and then poke two holes in the trimmer spool with a pointed object.
The holes should run through the center of the spool, allowing the trimmer line to pass through during the assembly.
To wind the trimmer line, begin with a sturdy piece of trimmer line. You can purchase trimmer line at any hardware or home improvement store. Cut a piece of line that is long enough to make two loops that pass through the two holes made in the trimmer spool.
Once the two loops have been fashioned by wrapping the line around your index finger, fold the loops in half and pass it through the two holes in the trimmer spool. Tie a simple knot and make sure the loops are tight.
Next, pull the ends of the trimmer line and begin to wind it around the spool in a clockwise fashion. When winding the spool, keep the tension consistent and make sure the whole line is wound evenly.
Make sure to fill the entire spool and to keep your fingers away from the spinning head.
After the whole line has been wound around the spool, replace the metal cap so that the trimmer head is complete. Your new trimmer head is now ready for use!
How does a string trimmer bump head work?
A string trimmer bump head works by automatically feeding out fresh line when the head is tapped on the ground, also known as bumping. This is a great way to quickly and easily extend the line when it’s running low.
The trimmer head will contain a spool of trimmer line, which can be either plastic or metal. To feed out more line, the user simply bumps the head on the ground and the trimmer line will extend, allowing the user to keep going without having to stop and manually extend the line.
The string trimmer head also includes a guard which keeps the line from flying out and hitting someone. In addition, some trimmer bump heads have a guard that will quickly break away if it encounters a large object or obstacle, such as a rock or tree root, in order to prevent damage to the trimmer and operator.
Why does my trimmer line not feed?
One possible issue is that the line may not be properly inserted, either by incorrect installation or by general wear and tear. If the line has come out of the spool, check to make sure it is properly tightened and that it is wound evenly and tightly around the spool.
If the line is too long, it will not feed. Once properly wound, make sure the line is fully inserted into the head before attempting to use it.
Another potential issue is improper tension. It’s possible that the spring located in the trimmer head may be too loose, causing the line to not feed. If this is the case, the spring will need to be adjusted or replaced entirely.
It is also possible that the line is frayed or broken. This is common with extended use and often occurs if the trimmer is overfilled with line. Check the line to make sure it is still intact. If necessary, replace it with fresh line to ensure it is feeding properly.
Finally, if the trimmer head is sufficiently clogged, it may cause resistance that prevents the line from properly feeding. Try carefully cleaning it out with compressed air, taking care not to cause further damage to the trimmer.
In order to ensure the trimmer line is properly fed, it is important to make sure the line is properly wound, the tension is correctly adjusted, the line is not frayed or broken, and the trimmer head is clear of debris.
If all of these measures are taken and the line still is not feeding, it is possible that the head itself may need to be replaced.
How do I remove the head from my Echo trimmer?
Removing the head from your Echo trimmer is a relatively straightforward process that should only take a few minutes. The first step is to unplug the trimmer from the power source. Once the trimmer has been unplugged, use a Phillips screwdriver to loosen and remove the two screws that secure the bobbin head to the trimmer housing.
Once the screws are removed, carefully pull the bobbin head away from the housing. Depending on the model of your Echo trimmer, the bobbin itself may have to be unscrewed from the head in order to completely remove it.
This is done by holding the bobbin securely and unscrewing the bobbin head. Once the head is removed, replacing it or installing a replacement should be a snap.
What are the two basic types of string trimmers?
The two basic types of string trimmers are gas-powered trimmers and cordless electric trimmers.
Gas-powered trimmers use small two-cycle engines that require a fuel and oil mixture. They are powerful, heavier, and are able to handle larger, tougher areas of grass like overgrown weeds and rough terrain.
Cordless electric trimmers are powered by rechargeable or replaceable batteries, making them quieter and easier to use. They are lightweight, quiet, and emission-free, but do lose power over time due to the battery running out.
These types of trimmers are better suited for smaller, even patches of grass. Both styles come in straight shaft, curved shaft, and wheeled models.
What is a bump feed trimmer head?
A bump feed trimmer head is a type of trimmer head used for cutting grass or weeds around buildings and hard-to-reach areas like sidewalks, fences, driveways, and edgings. The head is designed to easily release trimmer line when the user presses down on the bump knob located on top of the spool.
This type of trimmer head uses a single. 095-inch, round-profile trimmer line that is automatically fed through the trimmer, providing continuously fresh, sharp line for cutting. The advantage of this type of trimmer head is that no time is wasted manually pulling out line for replacement.
Additionally, a bump feed trimmer head is more economical than other style trimmers since it uses only one type of line and does not require the purchase of additional parts such as spools. Furthermore, this type of trimmer is extremely easy to use and requires little maintenance.
Is bump feed or auto feed better?
Bump feed and auto feed each have their own pros and cons, so it can be hard to determine which one is better overall. With a bump feed system, the user manually advances the line by tapping the head of the trimmer against the ground.
This type of system can be convenient, as it is lightweight, easy to use and takes up less storage space than an auto feed system. On the other hand, an auto feed system contains a spool of line that automatically advances once it has been used up.
This type of system is preferred by some people due to its convenience. It doesn’t require you to continually tap the head of the trimmer against the ground or manually push the spool of line, saving you some time and effort.
Ultimately, the decision of whether to choose a bump feed or auto feed system depends on your individual preferences. Bump feed is ideal for those that don’t mind tapping the head of the trimmer against the ground, whereas an auto feed system is better suited for those that want to save some time and effort and don’t mind spending a bit extra.
What does auto feed mean?
Auto feed is a feature found on certain types of printers, scanners and copiers. It allows for printed documents, photographs and other materials to be fed automatically through the device. This can save time and effort by streamlining the process of printing, scanning or copying multiple items without having to manually insert each item into the machine.
Auto feed is often used in offices and businesses where multiple copies of documents need to be printed or scanned in a short amount of time. Additionally, auto feed can be helpful when making copies of photographs and other items that require precision and accuracy—it ensures that each item is placed in the same location and orientation.
Auto feed can also be used to scan multiple items in a row, which saves time and prevents the need for manually transporting items from the scanner to the computer.
Is the Milwaukee string trimmer a bump feed?
Yes, the Milwaukee string trimmer is designed to be a bump feed. This feature allows you to easily add more line while you are using the trimmer without having to interrupt your work. Bump feeding gives you better control of the amount of cutting line you want and need for the job.
To reload the trimmer, simply bump the head of the trimmer on the ground. This will cause the spool to rotate, allowing new line to be fed through the trimmer. You can load as little or as much line as needed for the job.
This makes it easy to quickly switch between cutting thicker areas and trimming fine edges around your lawn, giving you greater control and precision.