The Black and Decker GrassHog is a corded electric string trimmer that is powered by a 6.5 amp motor. It boasts a 14-inch cutting width and a powerful dual line spool with a semi-automatic feed system.
The handle is adjustable and pivots to 7 different positions for added comfort. Additionally, it has an adjustable auxiliary handle and a lock-off switch to ensure user safety. The GrassHog comes with a 7-foot electric cord, meaning it can be used a decent distance away from an outlet.
The tool is lightweight, weighing only 7.6 pounds, making it easy to maneuver over large spaces and narrow areas. The GrassHog is ideal for trimming grass and weeds along driveways, around flower beds and edging along sidewalks.
Why won’t my Black and Decker weed eater won’t auto feed?
If your Black and Decker weed eater won’t auto feed, the most likely cause is an issue with the auto-feed head. This component is responsible for advancing the line when it becomes worn down during operation.
The most common issues with the auto-feed head include a lack of tension on the spool, which can prevent the line from advancing, as well as a failure of the spool from engaging with the motor. In order to fix these issues, the auto-feed head should be checked for any damage or blockages and the spool tension should be reset if necessary.
It’s also possible that the motor itself may be experiencing issues such as overheating or a loss of power, which can result in the auto-feed head malfunctioning. If this is the case, the motor should be tested and, if necessary, replaced.
Where is the model number on Black and Decker weed eater?
The model number for your Black and Decker weed eater can be found on the back or side of the machine, near the bottom. It may also be located on a metal plate on the motor housing. It will typically be preceded by ‘Model Number’ or ‘Mod. No.
‘, although it may just be a string of letters and numbers. If you have trouble locating it, check the owner’s manual or online product information.
What size trimmer line does Black and Decker use?
Black and Decker offers a variety of trimmer lines depending on the type and size of the trimmer that you have. For example, their electric models typically utilize a 0.065-inch diameter line, while their gas models require a different type and size of line.
They also offer larger trimmers that require a thicker line with a diameter of up to 0.105 inches. Furthermore, Black and Decker offers lines specific for edging, which are smaller in diameter and measure at 0.
065-inch for their electric models and 0.080-inch for their gas models. It is important to note that you should always refer to the user manual for the specific size of line that is recommended for your particular model.
How do I feed my Black and Decker trimmer line?
To feed your Black and Decker trimmer line, first make sure that the trimmer is disconnected from the power source. Then, take out the spool of trimmer line and remove the spool cap from the spool assembly at the top of the trimmer.
After that, insert the spool into the assembly and thread the line through the eyelet. To add more line, wind the trimmer line around the spool in an ‘S’ shape until it is full. Once it is full, reattach the spool cap and make sure it is securely fitted.
Finally, turn on the trimmer and hold the trigger down to let a small amount of line to feed from the spool. Release the trigger, and your line is ready to be used.
Does trimmer line size matter?
Yes, the size of trimmer line does matter. If the line is too thick, it will cause the machine to work harder and make it difficult to manoeuvre. A line that is too thin will not be as effective in cutting.
The size of the trimmer line will also depend on the type of grass and weeds being cut. If a tougher job needs to be done, then a thicker line should be used. On the other hand, if the grass and weeds are mostly fine grass, a thinner line should be used.
The thickness of the trimmer line is usually indicated on the packaging and should match the size indicated by the manufacturer of the trimmer.
What trimmer line is for edging?
When it comes to edging, most people prefer to use a round trimmer line. A round trimmer line creates a smoother and more even finish when compared to other types of line shapes. This is because the rounded shape of the line provides a greater surface area, which allows it to glide over the lawn.
Additionally, a round trimmer line is less likely to get caught on uneven surfaces or cause any additional damage to lawns or pathways. Other trimmer lines such as square or star may be suitable in some cases, but round trimmer line is definitely the go-to choice for edging.
How do you restring a Grasshog trimmer?
Restringing a Grasshog trimmer is pretty straightforward. Here’s a step-by-step guide to follow:
1. Unplug the trimmer from the power source and lay it down on a flat surface. Make sure the cutting head is sideways to avoid accidental injury.
2. Take off the outer shell by removing the screws using a screwdriver. Carefully remove the top cap and the spool.
3. Check and measure the inner spool to determine the length and diameter of the string needed.
4. Cut the string at least 3 inches longer than the spool. Feed the end of the line through the eye located on the inner spool and roll it around the spool.
5. If the trimmer has an adjustable knob located on the spool, make sure to adjust it to the correct tension.
6. Reinstall the spool with the line previously wrapped around it and the top cap, making sure it’s all symmetrical.
7. Replace the outer shell and align the screw holes. Tighten the screws until the trimmer is properly re-assembled.
8. Once the trimmer is reassembled, plug it in and test the trimmer to check that the string is properly wound and cutting correctly. If the trimmer is not working properly, then you will need to repeat the process or take the trimmer to an authorized service center.
How do you convert a string trimmer to a brush cutter?
In order to convert a string trimmer to a brush cutter, you will need to replace the existing string trimmer head with a plastic brush cutter blade. To do this, first disconnect the spark plug or power source from the trimmer.
Next, remove the trimmer head by taking off the spool retainer nut and then removing the old string trimmer head. Once the trimmer head is removed, use an adapter to attach the brush cutter blade. Finally, secure the blade to the trimmer shaft and then reattach the spark plug or power source before testing the converted brush cutter.
It is also important to use protective gear, such as safety glasses, when working with a brush cutter.
How do you put new line on a spool trimmer?
To put a new line on a spool trimmer, start by turning off the trimmer and unplugging it from the power source. Next, remove the trimmer head from the motor by pressing down on the locking tab and turning the head counterclockwise.
Now you should be able to see the spool. You can either replace the spool if it is damaged or exhausted, or if the spool is still good, use a pair of pliers to pull off the old line. Once the old line is removed, tie a knot at the end of the new line, wrap the line around the spool, and tie off the other end keeping tension on the line.
If a wand attachment is included with the trimmer, make sure there is no slack in the line. Replace the trimmer head by pushing down on the locking tab and turning the head clockwise until it locks into place.
Now plug the trimmer in and turn it on to test the new line.
How do you restring an electric weed eater?
Restringing an electric weed eater requires the following steps:
1. Unplug the string trimmer and remove the spool from the head.
2. Cut a length of trimmer line to the recommended length, usually around 25-30 feet.
3. Wrap the one end of the trimmer line around the spool’s center post and tie off in a knot.
4. Secure the line with the line retainer and insert the spool back into the head.
5. Pull the line taut and wrap in a clockwise motion, crossing in the center post each time.
6. Continue wrapping until the spool is full (leave about ¼ inch of space) and tie off the other end of the trimmer line to the center post.
7. Place the spool back into the head, replacing any protective cap or holding pins.
8. Reattach the head to the weed eater and plug the string trimmer back into its outlet.
9. Release the line retainer and pull the trigger to ensure the line feeds out of the head properly.
With proper maintenance, a new string should last several cutting sessions. Remember to replace the trimmer line when it becomes too worn or frayed to use.
Why does my strimmer wire keep coming out?
The most common cause is that the spool on the strimmer has become loose and slack. This can happen over time due to regular use, or could be the result of an accidental jolt to the machine. If this is the case, it can be solved by tightening the spool.
Another likely cause is that there’s a blockage somewhere in the mechanism. Strimmer wire can become tangled or knotted after prolonged use, preventing it from rewinding properly. It’s also possible that the line is frayed or has worn down.
The best way to address this issue is by checking the entire spool for any jams and replacing any worn-down wires.