Curtain tie hooks can be positioned in several places on your curtain depending on the type of hang you would like. Most people hang the hooks on the top of the panel near the top seam. You want to be sure to space the hooks evenly to ensure that the curtains hang evenly when they are opened.
The second place you can hang the hooks is midway through the panel. This will help when you want the curtains to be partially open, but still give you full coverage. Finally, you can also hang the hooks near the bottom seam.
This is most often used when you want a puddled look, with the curtain rings and fabric hanging slightly lower than the actual rod. Whichever method you chose, the key is to always ensure that the hooks are evenly spaced!.
Where do curtain hooks go on the wall?
Curtain hooks should be installed on the wall directly above where the curtain will hang. For the best result, you want to make sure the hooks are spaced evenly, and line up symmetrically on the wall.
You should also make sure the hooks are at least 5 inches above the top of the curtain rod. This will ensure that the curtain opens and closes smoothly. When drilling the holes for the hooks, make sure to use the appropriate drill bit for the type of wall that you are working with.
Afterwards, secure the hooks with a screwdriver. Lastly, make sure all the screws have been tightened properly, so that the hooks are securely in place.
How high should curtain holdbacks be?
When deciding how high to hang curtain holdbacks, the most important consideration is functionality. If the holdbacks are placed too high, they may be difficult to reach when it is time to open the curtains.
A good general rule of thumb is to install the holdbacks at least at the midpoint of the curtain top, or approximately at shoulder height when standing. This will ensure that the holdbacks are easily accessible, but also not too low to be considered unsightly.
Additionally, it helps to ensure that the curtains open and close without a struggle. When hanging curtains that are much taller than average, the holdbacks can be placed higher in order to accommodate the desired range of motion.
Likewise, when hanging curtains that are much shorter than the normal width, it is sometimes better to place the holdbacks lower than the midpoint in order to maximize the amount of light that can enter the window space.
Ultimately, there is no single correct answer for how high curtain holdbacks should be installed, and what works best will depend on the individual case and configuration of the space.
Where should tie backs be positioned?
Tie backs, or wall ties, should be positioned at the joints of the outer leaf and the inner leaf of a cavity wall. Typically, they are placed in a perpendicular formation and spaced at 600mm intervals in order to ensure the external wall is secured in place.
Depending on the design of the wall, the tie backs may have to be placed at different locations or even off-center to ensure the wall is properly secured. When installing tie backs, care should be taken to ensure the ties are flush with the wall and all ties are properly connected to the wall.
Depending on the material used and the strength of the wall, the installer may need to use high quality nails, bolts, and/or adhesives to ensure the ties are securely fastened to the wall. Additionally, the wall ties may need to be reinforced with additional ties to ensure the wall will remain completely secure.
Do curtains look better with tie backs?
Yes, curtains typically look better with tie backs. Tie backs enjoy the curtains from either side and help to frame the window. This gives a neat, orderly look and makes the window itself part of the room’s overall decor.
When the curtains are loose, they can easily fall in front of the window, blocking out the light and taking away from the overall look of the room. Tie backs also lend to straight and orderly pleating.
The fabric hangs smoothly and not only frames the window nicely, but also helps with insulation and darkening the room. Tie backs are typically attached with hooks and even come in many different styles and colors, so they can be tailored to any room’s unique style.
Lastly, curtains with tie backs can easily be opened and closed with just a simple tug of the ties. All in all, curtains look better with tie backs for many reasons, making a room look more polished and elegant.
Can you use tie backs with eyelet curtains?
Yes, you can use tie backs with eyelet curtains. Tie backs are a great way to keep curtains back when needed, as they serve a practical purpose as well as adding a decorative touch to your curtains. With eyelet curtains, the tie-back loops are usually sewn into the fabric, so it’s easy to simply add the tie backs if you’d like.
Tie backs can be made from thick cord or thin ribbons to match the fabric of your eyelet curtains. They can also be bought separately from the curtains and come in a variety of colours and styles. Tie backs are relatively easy to install, even if you do not have a lot of sewing experience.
All you need to do is feed the tassels of the tie backs through the eyelet holes on either side of the curtains, then tie or loop the tassels together at the middle. You can also add extra weight to the curtain at the bottom in order to keep it in place while the tie backs are on either side.
What is the correct way to hang eyelet curtains?
The correct way to hang eyelet curtains is to use a metal or wooden curtain pole that is the same width as the curtains. First, measure the width of the curtain pole and the curtains and cut the pole shorter if needed.
Next, attach the curtain pole to the wall using the appropriate fixings for your wall type. If needed, you may also need to attach corner brackets for extra support. Next, slide the eyelet rings onto the pole, making sure that they are evenly spaced.
Then, hang the curtains by looping the hole at the top of the eyelet onto the matching ring on the pole. Finally, secure your curtains in place by adjusting the length and tension of the pole. Once your eyelet curtains are hung, make sure to finish them off with a tie-back or curtain holdback to allow natural light in when needed.
Should eyelet curtains be double width?
It really depends on the size and configuration of your window and the look you are wanting to achieve. If you have a wide window and want to give it a less busy, airy look, then hanging a single panel of double width eyelet curtains is a great option.
However, if you want a more tailored look, then two standard width panels will likely be necessary. If you want to gain some extra privacy then you can use interlining to provide the extra layer, with the eyelet curtains still being a single width.
Ultimately, the decision of whether to use a single double width panel or two panels of standard width really comes down to personal preference and the effect you are trying to achieve.
How do you make tie backs for curtains?
Making tie backs for curtains is a relatively simple project that can quickly add a touch of sophistication to any window treatment. The following steps outline how to make tie backs for your curtains:
1. Start by measuring the curtains and decide how many tie backs you will need. Generally, tie backs should be spaced at least every 18 to 24 inches along the curtain.
2. Choose the fabric for the tie backs. A simple cotton blend or decorative fabric is often used.
3. Cut the pieces of fabric for the tie backs. Generally, the length should be two to three times the length of the curtain and the width should be two inches less than the width of the curtains. For example, if your curtain is 60 inches long and 30 inches wide, your tie back pieces should measure at least 120 inches long and 28 inches wide.
4. Fold the fabric over to make a double layer. Consider adding a layer of batting for added softness. Sew or glue along three edges, leaving one edge open.
5. Turn the tie back right side out. Place the loop so that it is on the outside, and use a flat piece of cardboard or ruler to press the corners flat.
6. Once the ties are complete, use tack nails or loops of fabric or ribbon to secure each tieback to the wall, taking care to space the tie backs evenly.
7. Gather the curtains into the hand and slip them inside the loop. Adjust the curtains to ensure they look even. Secure the tie backs snugly, but not too tight.
The end result will be curtains that look great, while adding a touch of your own style to the room.
How much fabric do I need for a tie back?
The amount of fabric you need for a tie back will depend on how large the window or curtain is. To figure out the amount of fabric needed for a tie back, measure the width of the window or the length of the curtain, then double it to figure out the circumference.
Take this measurement and multiply it by your desired length of the tie back. Generally, three feet is a good estimate for the tie back length. For two tie backs for a window that is two feet wide, you would need twelve feet of fabric.
If you are making a long, flowing tie back, you may want to use a bit more fabric.
Do curtains have to touch the floor?
No, curtains do not have to touch the floor. The length of your curtains is a personal preference and there is no strict rule. The choice of whether to have curtains that touch the floor, hang just above the floor, or hang well above the floor is a matter of taste.
Some homeowners prefer the look of a longer drape that reaches the floor, while others opt for a shorter curtain that doesn’t touch the floor and lets in more light. Ultimately, you should choose a length that looks and feels best for your space.