Typically, the tap for a freestanding bath is located at the end of the bathtub, from the same end where the drain is placed. This allows easier access and provides a more symmetrical design. When positioning the tap, it is important to consider the height and to work around any existing frame or frame supports.
Many manufacturers provide templates or guidance to ensure a standardised and professional installation.
Depending on the size and shape of the bathtub, the tap can also be located at the middle section of the bath. In this case, it is important to consider the flow of hot and cold water and also the user’s preference.
The tap should be able to reach the centrefold of the bathtub easily and should be located in an area where the user does not have to reach over the side of the bath.
Prior to installation of the tap, it is important to prepare the area for plumbing and fit the plumbing fixtures into the wall. This may involve drilling into the walls, and attaching a wall-mounted support for the tap.
Once the fixtures and piping are installed, the tap can be connected to the plumbing lines and secured into place. After installation, the area should be inspected for any leaks or other issues and any watertightness tests can be undertaken, if necessary.
How far should a freestanding tub filler be from the tub?
A freestanding tub filler should be placed about two feet away from the tub if it is a center-of-the-room type. If it is a wall-mounted tub filler, it should be installed two feet from the edge of the tub, which is the general rule of thumb for most tubs.
Ensure that the hot and cold water lines reach the valve. When plumbing is not near the tub, longer lines can be used. For example, the water lines for a freestanding tub can be about 10 feet in length.
Additionally, a diverter valve should be installed between the faucet and the wall. Most plumbing codes require a minimum distance separating the wall and the faucet, which typically falls between 6 and 24 inches.
Finally, plan room for drain lines to be connected to the bottom of the tub. They should be installed so the water flows into the drain without any obstructions. Ultimately, follow any pertinent building or plumbing codes to ensure you keep your bathroom safe and secure.
How far away from wall should freestanding tub be?
When installing a freestanding tub, the minimum distance recommended from the nearest wall is 20 inches (50 cm). This allows room for pipes and adequate circulation space. Additionally, if the tub does not have a skirted sides, it is recommended to leave at least 6 inches (15 cm) of space between the wall and the side of the tub.
This is so the sides of the tub are not covered with grout and can be cleaned easily.
It is also recommended to install a pre-made alcove around the tub to hide any pipes and valves. This can help to prevent water damage and increase the aesthetic of the bathroom. The space in between the alcove and the tub should be a minimum of 2 inches (5 cm).
In summary, the minimum recommended distance from a wall to a freestanding tub is 20 inches (50 cm) when no alcove is present and 2 inches (5 cm) with an alcove. Additionally, the space between the side of the tub and the wall should be at least 6 inches (15 cm) if skirting is absent.
Why are freestanding tub fillers so expensive?
Freestanding tub fillers are often quite expensive due to the range of features and finishes they offer. Not only do they need to be able to provide a reliable, high-quality water supply, they must also be stylish and offer a range of options for customising the tub to suit individual designs and tastes.
Depending on the finish and features, freestanding tub fillers may include floor-mounted spouts, a waterfall spout, hand-held showerhead, cross handles, and a variety of finishes. Many of these features add to the cost of the product which, when combined with the high quality and customisation possibilities, can make freestanding tub fillers rather pricey compared to other tub fixtures.
How much space is needed around a freestanding tub?
At least 18” – 24” of clearance space should be provided around each side of a freestanding tub for comfortable entry and exit. You should also make sure that the room allows for at least 60” of open space in the front of the tub for accessibility purposes.
Additionally, you should take note of the ceiling height of the room to ensure it is high enough to accommodate the height of the freestanding tub so you don’t have to worry about hitting your head. When measuring, be sure to also consider any accessories or details like towel racks, storage units, and shelving that can get in the way.
If the bathroom design includes plumbing fixtures, it is important to leave room around the tub for pipes, fittings, and other components related to the tub setup. Finally, it is important to take measurements prior to installation to ensure that your tub is a good fit and that all around clearances are met.
Can you put a freestanding tub against the wall?
Yes, you can put a freestanding tub against the wall. However, there are some things to consider when doing so. First, the tub needs to be on a level surface, which may require installing a platform.
Second, make sure there is easy access to a water supply and a drain line, as these would need to be installed or modified if the tub is near a wall. Third, you should consider making sure the walls can support the weight of a full tub and the water in it.
There may be special bracing and reinforcement needed if the walls are not load bearing. Finally, if you have a shower installed nearby, you should consider whether the shower will be able to reach the tub or if you need to use a hand held shower head.
Installing a freestanding tub against a wall can be done, but you must make sure you have the necessary considerations and preparations in place.
Can you use a wall mounted faucet with a freestanding tub?
Yes, it is possible to use a wall mounted faucet with a freestanding tub. Because these types of tubs are typically not secured in place, the plumbing fixtures must be securely bolted and connected to a nearby wall.
This helps ensure that the faucet produces enough water pressure for a steady flow. In order to ensure a water-tight connection and stable water pressure, it is important to consult with a professional plumber before installing a wall mounted faucet with a freestanding tub.
The plumber can help you select the correct size, style, and type of faucet and make sure all installation steps are properly completed. Additionally, the plumber can ensure that any necessary permits and inspections are taken care of.
How high should the tub spout be above the tub?
The ideal height for a tub spout should be about 6 to 7 inches above the finished rim of the tub. However, keep in mind that varying factors can cause this height to differ. For example, if you are installing a larger, deeper tub, the spout may need to be a bit higher, while a small, shallow tub may require a lower spout.
Also, think about the height of the person most likely to use the tub — you may want the spout higher or lower depending on the height of the individual. Additionally, be sure to check the directions of the specific spout you are installing, as some may require different measurements.
As a general guideline, 6 to 7 inches will usually provide the best bathing experience.
How far should tub spout stick out from wall?
The optimal distance that a tub spout should stick out of the wall is around 6 to 8 inches. This ensures that the spout is safely out of the way to prevent splashing and adequately reach the tub or shower where it is desired.
It also provides an aesthetically pleasing look and helps maximize the use of the space. Additionally, the length of the spout should be taken into consideration when measuring the optimal distance from the wall.
Spouts that are too far away from the wall may look awkward and can cause splashing. If the spout is too close, the water pressure may be too weak and make the shower or tub more difficult to use.
What is a deck mounted tub filler?
A deck mounted tub filler is a type of bathtub faucet that mounts directly on the top of the tub’s deck, or the surrounding support structure, rather than on the walls or in the floor of the bathroom.
It is a popular choice because it looks modern and stylish and can be more accessible, depending on the design. Deck mounted tub fillers are available in a variety of styles and finishes, so it is easy to coordinate them with the look and feel of the bathroom.
Most are constructed with solid brass construction and flexible hoses for easy installation and may have a hand shower for added convenience. Deck mounted tub fillers can be designed with a single handle or a double-handed model that offers separate hot and cold water control.
They may also have a diverter to switch the water from filling the tub to a hand shower as well.
Should a bath be fixed to the floor?
In general, it is recommended to fix a bath to the floor. When a bath is installed on the floor and not secured, it can be difficult to gain access to the pipework or any other parts underneath. In addition, the bath may move when a person is in it which can be very dangerous.
This could cause someone to slip and fall, or injure themself in some other way.
The most common type of fixing involves using screws to secure the bath to battens or supported base. If a bath is made from a heavy material such as cast iron or steel, it can also be securely fixed to a concrete or brick base.
Fixing a bath to the floor also helps to waterproof it – as no water can get underneath and cause any damage.
Whichever type of fixing is used, it is very important to ensure that it is installed correctly and in full accordance with the manufacturers instructions. This will ensure the bath lasts for many years to come and that it is safe for use.
Do free standing tubs go on top of tile?
Yes, free standing tubs can be placed on top of tile. This can be done with the use of a mounted support system that can be installed directly into the subfloor with the use of anchor bolts or powder-coated metal supports with adjustable feet.
When installing the tub, it should be properly leveled and set in place with flexible adhesive caulk. Silicon or polymer-based grouts should be used to seal the gaps between the tub and the tile, and the walls should be sealed using a perimeter sealant.
It is important to always contact a qualified professional or qualified tile installer when installing a freestanding tub on top of tile, to ensure that it is properly braced to carry the weight of the tub, while conforming to all local building codes.
Do you have to tile behind a freestanding bath?
No, you do not have to tile behind a freestanding bath. Depending on the type of bath you have, a tiled wall may not be practical or in some cases, even possible. With a freestanding installation, the wall mounts and floor brackets are used to securely install the bath, so any tiling work is optional.
If you do choose to tile the wall, it can add an attractive finish to any bathroom. Additionally, tiling can provide a waterproof layer to help protect your bathroom walls from water damage. However, if you don’t want to tile, you can instead opt for a waterproof panel.
These are designed to be easy to install and give your bathroom walls a finished look.
Do you install flooring under bathtub?
Yes, it is important to install flooring underneath a bathtub. This is the foundation of any good bathroom set up, as it helps to ensure that the basement or the floor beneath the tub is well protected from water penetration.
Typically, flooring should be installed before the bathtub is put into place, so that it can be adjusted as needed for proper fit and positioning. This can be anything from plywood and waterproofing materials to more structured and decorative types of floor tiles.
Doing this will prevent water damage and help maintain the quality and integrity of the floor and the area beneath it. Additionally, having a solid foundation beneath the bathtub will help properly support the tub, creating a safer and more durable installation.
Do you install a bath before or after tiling?
When it comes to installing a bath, it is best to do so after you have finished tiling the bathroom. This will ensure that your bath is properly supported and level within the tiled space. If you install the bath first, it will be much more difficult to fit the tiles around it, which could result in a substandard finish or uneven tiles.
Additionally, installing the bath first could put strain on the plumbing or the walls, which can cause damage or create problems down the line. Installing the bath after tiling also ensures that the edges of your bathtub are flush with the tiled area, ensuring a finished look.
Can you fit a bath over tiles?
Yes, it is possible to fit a bath over tiles. Depending on the type and size of the bath and tiles, it may be necessary to use an approved adhesive to attach the bath to the tiles to ensure it is held firmly in place.
Additionally, it is important to check that the area the bath is being fitted on is suitable with no signs of dampness or defects, as well as making sure the tiles are level and stable. Tiles located under the bath may need to be cut and sealed, and it is highly suggested to use a professional plumber to fit the bathtub to ensure it is secure.
Possible benefits of fitting a bath over tiles include a cleaner look, faster installation and lower costs.