The Supersaw is a synthesizer patch developed by Roland Corporation, a Japanese manufacturer of electronic musical instruments. First released in 1987, the original Roland Supersaw was designed to emulate the sound of the Yamaha DX-7 synthesizer.
The Supersaw is a seven-oscillator sawtooth-wave virtual synthesizer that relies on multiple detuned oscillators working in parallel to produce a full, rich tone. It has been used to create iconic sounds in electronic music across various genres, including house, techno,synthpop, and trance.
Today, Roland continues to develop patches and sound libraries for its synthesizers, including the Supersaw, making it one of the most popular synthesizer patch emulations.
How much does a STIHL 881 cost?
The exact cost of a STIHL 881 will depend on the specific retailer you purchase it from, as well as any applicable taxes or shipping fees. That said, the suggested retail price of a STIHL 881 is typically around $530.
This price includes the chain saw itself, a carrying case, and one chain. If you’re looking for additional chains, some retailers may offer a bundle pack for an extra cost. Furthermore, keep in mind that the exact cost of the STIHL 881 may vary due to seasonal discounts or other promotional offers.
How loud is a chainsaw in dB?
The noise level of a chainsaw can range from 95dB to 120dB depending on the size of the engine and the specific model of the chainsaw. Chainsaws can be extremely loud, potentially exceeding the OSHA standards for safe noise levels (85 dB).
To reduce the loudness of the chainsaw, hearing protection should always be worn and the saw should be used in an open area with no nearby structures to reflect the sound. Additionally, considering the work environment, reducing the amount of time the chainsaw is in use may also lessen the amount of noise produced.
How many decibels does a chainsaw give off?
The amount of decibels (dB) produced by a chainsaw can vary based on the brand and model of the chainsaw. However, in general, a standard gas-powered chainsaw produces around 110 dB when it is running at full power.
This is loud enough to cause potential hearing damage if a person is exposed to it for a prolonged time without wearing the appropriate hearing protection. For comparison, a normal conversation is typically around 60 dB and a car horn is around 110 dB.
Therefore, as one can see, chainsaws should be considered very loud and caution should be taken when operating one.
What is the dB of a police siren?
The dB of a police siren depends on the exact model and situation. Generally speaking, most police sirens are between 90-120 dB. This can vary depending on factors such as the police vehicle’s speed, nearby traffic, or any other ambient noise that could interfere with the sound.
Some sirens can reach up to 140 dB, which is louder than a jet taking off right next to you. It is highly recommended to keep a safe distance away from police sirens. Prolonged exposure to sounds over 85 dB can cause hearing damage.
How many dB is a nail gun?
The decibel level of a nail gun varies depending on a few factors, such as the type of nail gun, type of nails, and size of the nail. According to the Centers for Disease Control and Prevention (CDC), most residential motor-driven nailers generate noise levels of around 100 dB when measured from the operator’s position, with peak sound levels of approximately 110 dB.
Professional large nailers and driven pinners have typically been measured at noise levels of above 100 dB. The CDC also notes that continuous exposure to noise at or above 85 dB, for more than 8 hours, has the potential to cause noise induced hearing loss.
As such, it is important to always wear protective hearing equipment when using any motor-driven nailer.
Where do you put the oil in a mini chainsaw?
The oil reservoir in a mini chainsaw can be found on the side of the machine. This can be identified by the dip stick which is typically placed near the reservoir and will have a cap/cover on top of it.
When checking and refilling the oil, it is important to make sure the chainsaw is turned off and the spark plug wire has been removed to ensure the machine does not start accidentally. Carefully remove the cap and then use the dipstick or a funnel to fill the reservoir with the correct chainsaw bar oil.
Replace the cap, ensure the spark plug wire is reconnected and you’re ready to go.
How do you oil a mini cordless chainsaw?
Oiling a mini cordless chainsaw is a simple process, but it’s important to make sure you do it correctly. Before oiling the chainsaw, turn it off and disconnect the battery. Then, locate the oil hole, which is often on the side of the bar near the tip of the chainsaw.
Carefully insert the tip of the oil bottle into the hole and press it in until you feel resistance. Squeeze the bottle to gradually release the oil until it starts to come out of the hole. Once you’ve released enough oil, stop squeezing the bottle and remove it from the hole.
Use a cloth to wipe up any excess oil. After this process is complete, the oil should have fully lubricated the blades of the chainsaw. Before using the chainsaw, reconnect the battery and make sure it is working properly.
How do I lubricate my chainsaw?
To properly lubricate your chainsaw, you will need a few items: a can or tube of chain saw bar and chain oil, an oiler, a hand pump, and a scabbard.
First, clean your chainsaw and make sure it is turned off and the chain is not moving. Next, check the bar and chain oils in your chainsaw, which you can find on the owner’s manual. It’s important to use the specific type of oil recommended for your chainsaw to maintain its performance and life.
Before you start to add oil, place your chainsaw on a clean surface, like a workbench. Then, fit an oiler onto the end of the guide bar. This device looks like a bottle with a pump, and it will hold the oil and release an even, measured amount onto the chain.
Connect the oiler to the bar with a hose and secure it with the clamps. Pull the chain tight and adjust the pump pressure so that a drop of oil flows out each time the chain passes.
Once this is done, fill the oiler using the chain saw bar and chain oil, and turn on the pump. Make sure that the pump is not spraying too much, as this can damage the chain and reduce performance. If needed, adjust the pressure for a slower release of oil.
Finally, apply a thin sheen of oil to the bar and chain, inserting the scabbard between the chain and bar. This will keep the chain from rusting and wearing prematurely. When you’re done, turn off the pump and remove the oiler.
Don’t forget to clean any excess oil off your chainsaw!.
Can you use WD 40 to lubricate a chainsaw?
No, you should not use WD 40 to lubricate a chainsaw. Chainsaws rely on a specific type of lubricant, such as bar and chain oil, to keep the cutting chain in peak condition and to protect it from wear and tear.
WD-40 is a water-displacing formula that is designed to remove moisture, dust, and dirt from metal surfaces and protect them from rust and corrosion. It is not designed or intended to lubricate a chainsaw or its parts and using it could potentially damage the chainsaw or cause it to malfunction.
What oil can I substitute for chainsaw oil?
The type of oil used depends on the type of chainsaw you have. For those using a two-stroke gas powered chainsaw, you can substitute a high-grade synthetic two-stroke oil, as it has similar properties to the oil used for chainsaws.
For electric chainsaws, you can use a high-quality motor oil, such as SAE 30, as this is designed for small engines and has anti-wear properties which helps protect the motor. For cordless electric chainsaws, a light-weight motor oil, such as SAE 5W-30, is best as it will ensure maximum protection and efficient performance.
Additionally, you can use vegetable oil or even regular cooking oil in a pinch, but it may not provide the same level of protection or performance that other oils provide, so it’s best avoided.
Is WD-40 a degreaser?
No, WD-40 is not a degreaser; it is a multi-purpose lubricant, water-displacing spray, and penetrant product. WD-40 has many uses, including lubrication, cleaning, rust protection, and protection against moisture.
It is often used to loosen rusted bolts, clean bike chains and protect tools from rust and corrosion. The formula containing hydrocarbons and other additives makes WD-40 an effective solvent and grease cutter.
However, it is not intended to act as a degreaser; products like Simple Green or Greased Lightning are better suited for degreasing tasks.
Can you use engine oil for chainsaw bar oil?
No, you should not use engine oil for chainsaw bar oil. Engine oil is designed for use in automobile engines only, so it does not have the same protective qualities required for a chainsaw bar oil. Chainsaw bar oil is specifically designed to lubricate the bar and chain of your chainsaw to ensure maximum performance during use.
It is also formulated to reduce heat and friction while protecting the chainsaw parts from wear that could lead to breakdowns.
Can you polish wood with WD-40?
No, it is not recommended to use WD-40 as a polish for wood. WD-40 is designed for use on metal and other non-porous surfaces and can damage the surface of wood by leaving a residue. Instead, when polishing wood it is best to use products specifically designed for wood surfaces, like beeswax or furniture oils and polishes.
Applying the right product to the wood is important as different woods require specific types of polishes. For instance, pine and fir wood would require an oil-based polish, while oak and walnut wood require a wax-based polish.
Additionally, it should be noted that some polishes and oils are not suitable for certain finishes. If a piece of wood furniture has a shellac or lacquer finish, most wax-based polishes are not recommended as they may react with and damage the existing finish.
When in doubt, always check product labels and do a small test area first to make sure the product won’t damage the surface.
How do you clean a Stihl chainsaw after use?
To properly clean a Stihl chainsaw after each use, it is important to take the time to clean it thoroughly. Start by disconnecting the spark plug wire to prevent the motor from accidentally turning on while cleaning.
Use a clean cloth to wipe off any debris or saw dust from the exterior of the saw, and use a brush to brush any dirt or other residue away from the blades and chain. Then, use a damp cloth to clean the bar and chain to remove any residue or particles that can damage the chain during operation.
Finally, check the chain for any chips or damage. If there are any, replace it with a new chain and make sure to properly tension it before using it again.
Do battery chainsaws need bar oil?
Yes, all battery powered chainsaws need bar oil, which is a type of lubricant used to protect and allow for smoother operation of the chainsaw. Without bar oil, the chain on the chainsaw will stretch, overheat, and ultimately break.
Bar oil should be checked regularly, as well as before and after each use, to ensure the chainsaw is properly lubricated. Bar oil should never be overfilled, as this can cause the oil to spray onto the user and the surrounding area.
It is important to read the user manual for the chainsaw to know the proper amount of bar oil that should be used, as well as to ensure the type of bar oil used is compatible with the chainsaw.