If your MacBook Pro won’t turn on or charge, it’s likely due to a hardware or software issue.
First, check to make sure that the wall outlet and surge protector you’re using to plug in the adapter are working. If the power outlet is not working, the laptop won’t receive power and the battery can’t recharge.
If the power outlet is working and the laptop still won’t turn on, the issue may be related to the hard drive. Try resetting the SMC (system management controller) by doing the following:
* Shut down the Mac, if possible.
* Plug in the power adapter and fully insert the MagSafe connector into the power port, if possible.
* On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
* Let go, then press the power button to turn on the Mac.
If resetting the SMC doesn’t resolve the issue, then the issue could be related to the battery or logic board. In this situation, you should contact either Apple Support or an Apple-certified service provider to arrange a repair.
How do you fix a dead MacBook Pro that won’t charge?
If your MacBook Pro won’t charge, it could be due to a variety of issues. Troubleshooting a dead MacBook Pro that won’t charge is a process of elimination, so it may take some time before you can identify and resolve the problem.
First, try resetting the SMC (System Management Controller). This is a tiny chip on the logic board that regulates the laptops power settings. To reset your SMC, press and hold the left Shift, Control, and Option keys on your laptop, then press the power button at the same time.
Hold all four of these keys for 10 seconds, then release them and turn your laptop on.
If resetting the SMC didn’t work, then there may be a problem with the MacBook’s charger. If you have access to another charger that is compatible with your MacBook Pro, try using that to see if it resolves the issue.
If the second charger works, this confirms that the original charger is defective.
If the charger is not to blame, the next step is to take a look at the battery. On the MacBook Pro, there is a little reset button for the battery. It is a small pinhole located near the power cable.
Using a paper clip, press the reset button for 2-3 seconds and then release it. Then try to turn on the laptop.
If none of these steps worked, you may need to take the laptop to an Apple store or a service center to have them diagnose and fix the problem. Apple technicians will have the right tools and parts to replace any damaged parts that are preventing your laptop from charging.
Why is my MacBook Pro not charging when plugged in?
This could be caused by a few different things. First, check the power cable and make sure it’s securely plugged into both the power outlet and your MacBook Pro. If the power cable is securely plugged in and the power adapter light is not appearing, then it’s possible that the power cable or adapter has gone bad.
In this case, you will need to replace the power cable or adapter.
Another possibility is that your battery may be damaged. This can happen if the laptop has sat in a very hot environment or been exposed to moisture. To check this, first run your laptop while it is unplugged and see if the battery still holds a charge.
If it does not, then you may need to replace the battery.
Finally, it’s possible that the MagSafe port in your laptop is damaged. This is a very delicate port and can be easily exposed to damage. If it is indeed the MagSafe port, you may need to take the laptop to a repair center to get it fixed.
How do I fix my MacBook if it wont turn on or Mac?
If your MacBook will not turn on or boot, first try resetting the SMC (System Management Controller). This can often fix MacBooks that are not starting up properly. To reset the SMC on a MacBook that uses a non-removable battery, the following steps should be followed:
1. Shut down your MacBook
2. Press and hold the power button for at least 10 seconds
3. Release the power button
4. Press the power button again to turn your MacBook on
If the SMC reset does not work, it is possible that the cause of the issue is hardware related. In such a case, you should take your MacBook to an Apple Store or authorised reseller so that the hardware can be assessed by a qualified technician.
Alternatively, contact technical support for further help.
How do I revive my MacBook Pro?
If you want to revive your MacBook Pro, the first thing you should do is check the battery life. If it needs to be recharged, plug it in and see if it turns on. If it’s not working, you should try resetting the System Management Controller (SMC).
This can be done by turning the laptop off and then holding down the left side Shift+Control+Option+Power buttons simultaneously for about 10 to 15 seconds. Once you hear the boot sound, release the keys and the SMC should be reset and hopefully your MacBook Pro will start up.
If resetting the SMC does not work, then you may need to boot from extrnal media. To do this you will need to restart the computer and press and hold the Option key as soon as you hear the startup sound.
A list of available startup discs will then appear, and you can select which one you would like to boot from.
If those steps do not work, then you may need to perform a diagnostics check. To do this, hold the D key while restarting your laptop and it will start up in the Apple Diagnostics tool. This will run a series of tests to check for any hardware or software issues with your laptop.
If the issue persists after trying all the above steps, then you may need to take it to a certified Apple technician and have them take a look at it to see what the issue is.
How do I start up my Mac that won’t start up?
If you are having trouble starting up your Mac, there are a few different things you can try. First, try to reset the Mac’s System Management Controller (SMC). To do this, hold down the “Shift-Control-Option” and “Power” keys simultaneously for 10 seconds.
If that doesn’t work, you can try booting into Safe Mode. To do this, power on the computer and press and hold the “Shift” key as soon as it turns on. Release the Shift key when the Apple logo appears.
This will boot your computer into Safe Mode and may help resolve any issues that have been preventing it from booting normally. If these steps don’t work, you can try resetting the NVRAM (non-volatile random-access memory).
To do this, turn off the Mac and turn it on again and immediately press and hold “Option-Command-P-R”. Continue holding the keys for at least 20 seconds, then release the keys and wait for the Mac to reboot.
If this still doesn’t resolve the issue and you’re still having a problem starting up your Mac, you may want to try reinstalling Mac OS X. Do this by inserting your Mac OS X disk into your Mac, turning it on and letting it boot from the disk.
Select “Reinstall Mac OS X” and then follow the instructions. If you still have no luck, it may be time to consult an Apple technician who can further assist with your startup issue.
Why is my MacBook Pro screen black and not turning on?
First, it is possible that the power cable may not be plugged in properly or completely. It is also possible that the battery is completely drained and needs to be charged. Additionally, an overloaded RAM or a faulty logic board may prevent your MacBook Pro from turning on properly.
If all else fails and the screen remains black, it is possible that the display may need to be replaced or the machine may be experiencing a hardware failure. In short, there are a few potential causes that should be explored in order to determine the exact cause of your MacBook Pro’s screen being black and not turning on.
How do I restart my MacBook Pro when the screen is black?
If your MacBook Pro’s screen is black and it will not turn on, the best way to restart the device is to force it to restart. To do this, you need to hold down the power button for about 10 seconds until the computer turns off.
Once the device has completely shut down, press the power button again to boot up your laptop.
If your MacBook Pro won’t start after forcing it to restart, you may need to reset the System Management Controller (SMC). First, you will need to shut down your computer and unplug all external power sources.
Next, press and hold the “Shift-Control-Option” keys (on the left side of the keyboard) and the power button at the same time. Hold all four buttons for 10 seconds and then release them together. Finally, plug your computer back in, press the power button and see if it turns on.
Resetting the SMC should get your MacBook Pro’s screen to turn on, but if it doesn’t, then you may need to take your device to a repair shop or contact Apple support.
How do you force restart a MacBook Air?
The process to force restart a MacBook Air is relatively straightforward.
Step 1: Press and hold the power button until the Mac shuts off or restarts. This will typically take a few seconds.
Step 2: Once the Mac has shut down, press the power button again to start it up again. This will take several seconds longer than usual to startup.
Step 3: Once the Mac has finished rebooting, it should be ready to use like usual.
It is important to note that it is not recommended to do a force restart on a Mac with any regularity as it can potentially cause data loss or corruption. It should only be done as a last resort if the Mac is not responding to usual instructions or has locked up and needs to be restarted.
Why is my Mac plugged in but not charging?
The battery may be faulty, or it may not be receiving enough power. If the battery is old, overheated, or drained, it may not be receiving enough power to charge effectively. In some cases, the power supply itself may not be capable of providing a full charge.
Additionally, running very intensive programs, such as games and graphic-intensive software, may prevent proper charging due to the amount of power they consume. Finally, the charging port may be damaged or dirty, preventing the power connection from being recognized.
To troubleshoot, you should try a different power source or adapter, try resetting the System Management Controller (SMC), check for debris or damage in the charging port, or if the battery is particularly old, consider replacing it.
What happens when Mac runs out of battery?
When Mac runs out of battery, your Mac will enter sleep mode and the display will shut off. Once the battery completely runs out, your Mac will completely shut down. This means you will lose all of your unsaved data and recent activity.
To prevent this, try to keep your battery charged above 20% and regularly save your data. Additionally, keep track of your battery level and power preferences and make sure your Mac is plugged into a power source when you need to work on something important.
How much does a Mac battery cost?
The cost of a new battery for your Mac will depend on the specific model and year it was manufactured. Prices can range from as little as $34.99 to over $200 depending on the model. The more recent the Mac, the higher the price of the battery.
Some third-party companies offer cheaper alternatives, but you should use caution when selecting a replacement battery as the quality may be lower than that of an Apple-authorized battery. To ensure you get the right battery and to guarantee its quality, it’s best to purchase an Apple-authorized replacement directly from Apple or their authorized reseller.
How do I start my Mac with a dead battery?
If your Mac has a dead battery, you should first try to identify if the battery is causing the startup issue by disconnecting it. To do this, turn off your Mac and press and hold the power button for ten seconds to drain any remaining electrical charge from your Mac.
If your Mac turns on without the battery connected, this usually indicates that the battery is not providing healthy power requirements to boot up the machine.
If the issue persists, you might need to charge the battery using a power supply. If the battery is removable, you can consider replacing it with a new one. If it is built-in, a professional technician may need to be consulted in order to assess and repair the battery.
In some cases, where the battery cannot be easily disconnected or replaced, it may be possible to start up your Mac using safe mode. To enable safe mode, press and hold the power button until you hear the startup sound.
Then press and hold the Command + Shift + S keys immediately. Your Mac should now start up and you can find the necessary options under the system preferences.
It is also important to remember to back up your system regularly, as it is always possible that your battery could malfunction. Taking regular backups will ensure that, even if the worst happens, you will not lose any important data.
How long does it take for a MacBook Pro to turn on after being dead?
The amount of time it takes for a MacBook Pro to turn on after being dead will depend on several factors, such as how recently the device was used. Typically, if the device has been powered down for a while, it typically takes anywhere from thirty seconds to one minute for a MacBook Pro to power up.
On the other hand, if the device is put into sleep or hibernation mode, instead of being completely powered off, then the time it takes to begin running again is significantly reduced, often to the range of five to ten seconds.
In either case, the time it takes for the MacBook Pro to turn on after being completely powered off will vary depending on the specific device, as well as its age and other factors.
Why is my Mac battery on hold?
Your Mac battery may be on hold due to a number of reasons. It could be that your Mac is in a low power mode and not charging, your battery may have suffered significant damage, or your Mac may not be calibrated properly.
Low Power Mode: If your Mac is in Low Power Mode, it will not charge the battery. To turn off this setting, go to System Preferences > Energy Saver and uncheck the box for “Enable Power Nap” or “Enable Power Adapter.
” This will allow your Mac to charge again.
Battery Damage: If you notice that your battery is not staying charged for very long, it may have suffered damage due to over-discharge or being exposed to extreme temperatures. In this case, you may need to replace the battery.
Calibration: Your Mac’s battery may also be on hold if it hasn’t been properly calibrated. You should periodically recalibrate your battery in order to keep it working properly. To calibrate it, charge your battery to full and then leave it plugged in for an additional two hours.
Then you can discharge the battery completely and then charge it fully again. This should reset the battery and make sure it is ready to go.
If your battery is still on hold after trying these methods, it may be necessary to bring in your Mac to a repair shop to have them check it out.
Why the battery is not charging?
The most common is that there is an issue with either the charger or the charging port on your device. A broken or damaged power plug or USB cable could prevent the battery from charging properly. You could also have an issue with the battery itself, such as a defective battery or a battery that is not designed for your device.
In addition, an incorrect charger, low voltage, or simply an old battery pack could also be the cause of your battery not charging properly. Finally, if you’re using a laptop, it’s possible you may have a bad connection between the charger and laptop, or the laptop may be set to not accept external power.
To determine the cause of your battery not charging, you should check the following:
1. Check the charger and power cord for any damage.
2. Check the port on your device to make sure it is clean and free of debris.
3. Make sure the charger is compatible with your device.
4. Make sure the outlet you are using is providing enough power (optimal range is between 110-240V).
5. Try a different outlet, or use an alternative power source such as an external battery pack or laptop power adapter.
6. Check your laptop settings to make sure it is set to accept power from an external source.
If you have tried all of these steps and you still cannot charge your battery, it may be time to visit a repair shop to have your device inspected for potential hardware issues.
Can I charge my Mac when it’s shut down?
Yes, you can charge your Mac when it’s shut down. The MagSafe connector or Thunderbolt port on your Mac will continue to provide power even when the computer is powered off. It may take longer for your computer to charge when it’s off or in sleep mode, but it will still charge.
To ensure your computer is charging, make sure the green light is on near the power connector. If the light is off, make sure the MagSafe or Thunderbolt connector is firmly attached to your Mac, and the other end is properly plugged into the power outlet.