First, try fully charging them by plugging the charging cable into a power source and leave it until it is fully charged. If they are still not turning on, try resetting them. If you have an AirPods case, place your Raycon Earbuds into it and close it for at least 15 seconds to reset.
If your Raycon Earbuds still will not turn on, the hardware may be having an issue. If this is the case, you can contact Raycon Customer Service for further assistance.
How do you fix earbuds that won’t turn on?
If your earbuds won’t turn on, the first thing you should do is check to see if they are charged. The majority of earbuds today are powered by a rechargeable battery and will need to be charged in order to function.
Most earbuds come with a charging cable that can be used to plug into a USB port or a wall charger. Check the connection between the earbuds and the charging cable to make sure it is secure and fully plugged in.
Depending on the type of earbuds, it can take a few hours for them to charge fully.
If they were already fully charged, try resetting the device. This can be done by holding down the power/play button and the volume down button simultaneously for a couple of seconds. You may also need to hold down the power/play button for a few seconds until the device resets itself.
If none of the above works, then it’s time to do a bit of troubleshooting. Check to make sure the earbuds are not blocked or damaged in any way and that there is no debris stuck in the charging port.
If none of these are the issue, then the problem may lie with the earbud’s internal components, such as the battery or the wiring. In this case, you will need to take the earbuds to a professional for further inspection.
How do I hard reset my Raycons?
If you would like to perform a hard reset on your Raycons, the best way to do this is to disconnect your headphones from any source and turn them off. This will completely clear any stored information that was previously stored on the device.
Once the headphones are off and disconnected from any source, press and hold both the volume + and – buttons for 10 seconds. This will initiate a hard reset on the device, clearing all settings and preferences.
After 10 seconds, the device will reset and be ready for you to use once again.
It is advised to perform this process if your headphones are having any difficulties or are not responding to any of your commands. This will give you a fresh start with the device and hopefully help with any troublesome issues that may have been present.
How do you reboot raycon earbuds?
If you need to reboot your Raycon earbuds, the process is pretty easy.
First, remove the Raycon earbuds from your ears and make sure they are disconnected from any Bluetooth source.
Once they’re not connected, hold down the power/function button on the headphones for 15 seconds. You will see the LED light slowly blinking, which indicates the headphones are rebooting.
Once the headphones are rebooted, you can pair them again with your device. To do this, turn on your Bluetooth connection and then hold down the button for 5 seconds and wait for the LED to blink. Once the light is flashing rapidly, you will be able to connect to the headphones.
Once the headphones are connected, you should be all set to start using them again and should experience increased sound quality.
What do you do if one of your raycon earbuds don’t work?
If one of your Raycon Earbuds does not work, there are a few steps you should take. First, try to reconnect it to your device. To do this, turn the earbud off and restart the Bluetooth connection from the device.
Make sure that the earbud appears in the device’s Bluetooth list of devices.
If the reconnection does not work, try to restart both earbuds. To restart the earbuds, turn them off and put them in their charging case for 1 minute. After one minute, take them out and turn it on again.
This will often reset any connection issues you may be experiencing.
If the issue persists after resetting the earbuds, the issue may be hardware-related. You should contact Raycon customer service to request a new product or warranty. Raycon offers a 1-year warranty on all their products and they may be able to repair or replace your earbud if the issue is covered under the warranty.
How do you put raycon earbuds into pairing mode?
To put your Raycon earbuds into pairing mode, you will need to hold down the power button and the volume down button simultaneously for 3-5 seconds. The LED indicator light will begin to blink quickly, indicating that the earbuds are in pairing mode.
Once the light has stopped blinking and is a solid color, your earbuds are connected. You can now connect your earbuds to your phone or another device. To do this, make sure both earbuds are in pairing mode and then open your device’s Bluetooth settings.
Select the Raycon earbuds and wait for the connection process to finish. Once connected, you should be able to listen to music or take calls with ease.
Why is my Raycon flashing red and blue?
If your Raycon headphones are flashing red and blue, it means that the device is either in pairing mode or needs to be reset. When a device is in pairing mode, it means that the headset must be connected to a Bluetooth device such as a phone, laptop, or other audio device using the included charging cable and an adapter.
To put the headphones into pairing mode, press and hold the power button for 3 seconds until the indicator light on the right ear cup blinks red and blue. Once in pairing mode, the device should now appear on your device’s Bluetooth list.
Once connected, you can stream audio and take calls directly from the headphones.
If your Raycon headphones are already connected to a Bluetooth device but are still flashing red and blue, this means the device needs to be reset. To reset the headphones, disconnect them from any audio device.
Then, press and hold the power button for 8 seconds until the LED on the right ear cup flashes red and blue. Reconnect the headphones to your audio device and resume using them as normal.
If the problem persists, contact Raycon customer service for further assistance.
How do I turn on my raycon earbuds without a case?
Turning on your Raycon earbuds without a case is fairly easy. First, locate the power/pairing button located on the inner side of the earbud. Press and hold the power/pairing button for at least 7 seconds.
Once the LED light flashes blue and white, your earbuds will be powered on and in pairing mode. You can then connect your earbuds to your device of choice.
You may also want to turn on your earbud’s auto-reconnect feature. This feature allows your earbuds to connect to your device once they’ve previously been paired and powered on. To turn on auto-reconnect, press and hold the power/pairing button on both earbuds for at least 7 seconds.
The LED light will then flash blue and white, signifying that the auto-reconnect feature has been enabled.
Once you’ve completed these steps, your Raycon earbuds should be powered on and ready for use. Whenever you want to turn on your earbuds in the future, you can simply press and hold the power/pairing button on the inner side of the earbud for a few seconds.
Happy listening!.
Do Raycons have a button?
Yes, Raycons have one multifunction button that is used to control the headphones. This button can be used to turn the headphones on or off, adjust the volume levels, play or pause music, answer or end phone calls, and even activate your phone’s voice assistant.
Additionally, with some models, the multifunction button can also be used to skip tracks and access different preset sound modes.
Can raycon earbuds be used independently?
Yes, Raycon earbuds can be used independently. Each earbud is equipped with Bluetooth technology, allowing them to pair with any compatible device and be used independently from the other earbud. The sound quality and performance of the earbuds will basically remain the same no matter which one you choose to use.
Additionally, Raycon earbuds have 6 hours of battery life when used independently, so you won’t have to worry about running out of power quickly. If you need to charge them on the go, you can easily stash them in the included case and get an extra 24 hours of battery life.
All in all, Raycon earbuds are designed to be used independently, and they’ll provide great sound quality and battery life no matter which one you choose to use.
How do I check my Raycon battery level?
To check your Raycon battery level, you need to access the battery indicator light found on the left earbud. When you first activate your Raycon, the indicator light will flash white. When there are approximately 20% or less of battery remaining, the indicator light will flash red.
You can also check the remaining battery level via the Raycon Global mobile app. Simply open the app, select ‘My Devices’, and you will be able to view the remaining battery level.
Do Raycon earbuds have touch control?
Yes, Raycon earbuds have touch control. For example, the Raycon E25 earbuds come with touch control support, allowing you to easily manage your music, take calls, and access your voice assistant with just a tap or a light squeeze of the earbud.
The right earbud can quickly answer/end calls, play/pause music, or access your voice assistant with just a tap, and the left earbud has a light squeeze sensor to cycle through your music and adjust the volume.
Additionally, Raycon includes a volume-optimized EQ that offers full range sound without distortion, even at louder volumes.
Can you skip songs with raycon earbuds?
Yes, you can skip songs with Raycon Earbuds. Raycon earbuds are compatible with a variety of devices, including smartphones, tablets and computers. To skip a song, simply press the ‘next’ or ‘skip’ button located on the earbud.
The specific location of the button will vary depending on the model you’re using, but it’s typically located on the outside of the earbud. Another option is to use the volume buttons. It’s also possible to skip a song using your device.
On most smartphones, you can simply swipe your finger across the screen. For more specific instructions, refer to the user manual for your device.
Can I replace one Raycon?
Yes, you can replace just one Raycon. If the product you are looking to replace is one of the following models, then you can purchase the replacement directly from Raycon: E10, E20, E25, E55, E50, E55 Plus, E55C, E55C Plus, R1 Pro, or R2 Pro.
If you are looking for a replacement for any other model, then you will need to contact Raycon Support for assistance. When you contact Support, you will need to provide them with the product serial number so that they can identify the correct replacement part for you.
Once you’ve received the replacement part, you can contact Raycon Support for technical support to help guide you through the replacement process.
What does the button on Raycon case do?
The button on the Raycon case is a power button. When pressed, it will turn the Raycon headphones on and off. If the headphones are already turned on, pressing the button for a few seconds will put them into pairing mode so that they can be linked to other Bluetooth devices.
The button also acts as a reset switch if there are any glitches or connection issues with the headphones. Depending on the model, there may be additional functions that the button can perform, so it’s important to refer to the user manual to find out more information.
Why is my left Raycon not working?
It is possible that your left Raycon is not working because of an issue with the power supply, the connection or a manufacturing defect. If you have tried charging it and it still isn’t working, the most likely culprit is a power supply issue.
This can be rectified either by plugging it in and charging it for a few hours until the battery is full or by using a USB cable and charging it for a few hours. If the charge still doesn’t seem to be working, it may be a connection issue.
You can try connecting it to the left side port of your device rather than the right side port to check this. Finally, if neither of these approaches work and all of the connections are checked and in working order, it is possible that you may be experiencing a fault or a defect with the device itself which may need to be verified by a technician or replaced.
What do the lights on raycon earbuds mean?
The lights on Raycon earbuds will indicate the current state of your earbuds. Generally, a white light indicates the device is powered on and is connected to your device. A blue light indicates that the device is connected and ready to pair, and a blinking light (in either color) indicates that the device is in pairing mode.
Additionally, the case may have a light that will be lit or flashing in various colors depending on the charge status of the case. A solid light indicates the case is charging and a fast flashing light indicates the case is fully charged.
How do I know when my raycon fitness earbuds are fully charged?
Your Raycon fitness earbuds will be fully charged when the LED light on the case turns from red to white. To charge the earbuds via the case, ensure the earbuds are placed into the case and close the lid.
Then plug the charging cord into a USB port or wall adapter and finally, connect the smaller end of the cable to the charging port at the back of the case. To maximize charging, avoid any use or obstruction of the charging port.
When the LED light on the front of the case turns from red to white, your Raycon fitness earbuds will be fully charged.